Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EnGLIsH
12 V CORDLESS ADJUSTABLE CLUTCH DRILL/DRIVER/
HAMMERDRILL
DCD716
WARNING: Read all safety warnings, instructions,
illustrations, and specifications in this manual,
including the battery and charger sections provided in
an original tool manual or the separate Batteries and
Chargers manual. Manuals can be obtained by contacting
Customer Service (refer to the back page of this manual).
Technical Data
Voltage
Peak
Rated
Type
Battery type
No-load speed:
1st gear
2nd gear
Impact rate
1st gear
2nd gear
Max torque (hard/soft)
Power output (MWO)
Chuck capacity
Maximum drilling capacity:
Wood
Metal
Masonry
Weight (without battery pack)
Noise values and/or vibration values (triax vector sum) according to
EN62841-2-1:
L
(emission sound pressure level)
PA
L
(sound power level)
WA
K (uncertainty for the given sound level)
Drilling into metal
Vibration emission value a
h,D
Uncertainty K =
Impact drilling
Vibration emission value a
h,ID
Uncertainty K =
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
18
DCD716
V
DC
V
DC
min
-1
min
-1
0–1500
min
-1
min
-1
0-22500
Nm
W
mm
mm
mm
mm
kg
dB(A)
dB(A)
dB(A)
2
=
m/s
m/s
2
=
m/s
2
m/s
2
WARNING: The declared vibration and/or noise emission level
represents the main applications of the tool. However, if the tool is
used for different applications, with different accessories or is poorly
maintained, the vibration and/or noise emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or noise should
also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
12
and the accessories, keep the hands warm (relevant for vibration),
10.8
organisation of work patterns.
1
EC‑Declaration of Conformity
Li-Ion
Machinery Directive
0–400
Drill/Driver/Impact Drill
DCD716
0-6000
D
WALT declares that these products described under
e
Technical Data are in compliance with:
30/16
2006/42/EC, EN62841-1:2015+A11:2022, EN62841-2-1:
2018+A11:2019+A1:2022+A12:2022.
180
These products also comply with Directive 2014/30/EU and
10
2011/65/EU. For more information, please contact D
the following address or refer to the back of the manual.
20
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
10
8
0.98
Markus Rompel
Vice-President Engineering, PTE-Europe
D
WALT, Richard-Klinger-Strasse 11,
e
88.5
65510, Idstein, Germany
22.12.2023
96.5
a
WARNING: To reduce the risk of injury, read the
5
instruction manual.
Definitions: Safety Guidelines
<2.5
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
1.5
these symbols.
DANGER: Indicates an imminently hazardous situation
10.1
which, if not avoided, will result in death or serious injury.
1.5
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
WALT at
e
WALT.
e
Werbung
