After Use; Maintenance Schedule; Vacuum Shoe Maintenance; Spray Nozzle Maintenance - Nilfisk 56314019 Bedienungsanleitung

Inhaltsverzeichnis

Verfügbare Sprachen

AFTER USE

When ﬁ nished cleaning, press the Scrub Off Switch (B), this will automatically raise, retract and stop all the machine systems (brush, vacuum &

solution). Then drive the machine to a service area for daily maintenance and review of other needed service up-keep.

To empty the solution tank, remove the Solution Drain Hose (4) from its storage clamp. Direct the hose to a designated "DISPOSAL SITE" and remove

the plug. Rinse the tank with clean water.

To empty the recovery bladder, pull the Recovery Bladder Drain Hose (21) from its storage area. Direct the hose to a designated "DISPOSAL SITE"

and remove the plug (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled ﬂ ow of waste water). Rinse the Waste

water Bladder (19) with clean water.

Remove the Brushes, rinse with warm water and remove any built-up string, hair or carpet ﬁ bers.

Disconnect the Recovery Hose from the Recovery Tank and ﬂ ush with warm water to wash any debris out of the Recovery Hose / Vacuum Shoe

Assembly.

Remove the debris hopper and clean thoroughly. Remove from left or right side of machine by lifting hopper up and tilting it forward then pull out.

Check the maintenance schedule below and perform any required maintenance before storage.

MAINTENANCE SCHEDULE

Check/Clean the vacuum motor foam ﬁ lter(s)

Check Foot/ Parking Brake for Wear & Adjustment

Purge the Detergent Injection System (EDS models only)

* Have Nilﬁ sk check the vacuum motor carbon motor brushes once a year or after 300 operating hours. The brush and drive motor carbon brushes check

every 350 hours or once a year.

NOTE: Refer to the Service Manual for more detail on maintenance and service repairs.

Store the machine indoors in a clean dry place. Keep from freezing. Leave the tanks open to air them out.

Turn the Master Key Switch (J) OFF (O) and remove the key.

VACUUM SHOE MAINTENANCE

Check the vacuum shoes daily, they can be removed to aid in cleaning, see "Removing the Vacuum Shoes". Remove any built-up string, hair or carpet

ﬁ bers.

SPRAY NOZZLE MAINTENANCE

Remove the spray nozzles once a week. Soak the nozzles overnight in a vinegar and water solution to remove chemical deposits.

LUBRICATING THE MACHINE

Once a month, pump a small amount of grease into each grease ﬁ tting on the machine until grease seeps out around the bearings.

Grease ﬁ tting locations are:

•

Steering Wheel Shaft Universal joint

Once a month, apply light machine oil to lubricate the:

•

Steering Chain

•

General Pivot Points For the Brush Deck Linkage

CLEANING THE VACUUM MOTOR FILTERS

Clean the vacuum motor ﬁ lters daily with compressed air. For extremely dirty ﬁ lters, wash with warm, soapy water and rinse thoroughly with clean water.

Allow the ﬁ lters to dry completely before re-installing in the machine. MAINTENANCE NOTE: Keep a second set of ﬁ lters on hand to use while ﬁ rst set is

drying.

POWER BRUSH MAINTENANCE

Check the brushes daily. Remove any built-up string, hair or carpet ﬁ bers. Check the bristle length. Have a service technician change the brushes when the

brush bristles are worn to 1/2 inch (12.7 mm).

revised 3/06

MAINTENANCE ITEM

Charge Batteries

Check/Clean Tanks & Hoses

Check/Clean/ Power Brushes

Check/Clean Vacuum Shoes

Check/Clean Vacuum Shut-Off Float

Empty Debris Hopper

Clean Spray Nozzles

Check Each Battery Cell(s) Water Level

Inspect Brush Deck Skirts