Troubleshooting - Steinbach 061014 Bedienungsanleitung

EN
Care and Maintenance
Cleaning the filter bag
Unfold the retaining ring and open the cleaner. Figure 21,22
Press the buckle on the base of the cleaner and take off the filter
cartridge. Figure 23,24
Take off the filter bag, drain and clean it and put on the filter bag
again. Figure 25,26,27
Important
Please press the buckle to remove or restore the filter cartridge. If
this is not observed, it may cause damage to the lower part of the
cleaner.
Press the buckle simultaneously. Figure 28
•
Do not pick up the two parts of the cartridge at the same
•
gure 29
The installation must be initiated from one
•
Press the buckle. Figure 31
•
Press the buckle on the other
•
Lift out the filter cartridge from one
•
Install the filter cartridge. Figure 34
•
Remove the filter cartridge. Figure 35
•
Remove bzs. Assembly of the filter
Tips and advices
• Each time the cleaner is removed from the water, the filter element
has to be cleaned.
• The pH-value of the pool water must be between 7.0 - 7.4.
• The water temperature must be between 10 ° C and 32 ° C.
• After pressing the "power off" button, the "power on" button can't
be pressed for 30 seconds.
• We recommend to keep the cleaner between 5 ° C and 40 ° C in a
shaded, well-ventilated place. The supply cable must be wound up
for storage. (The float on the cable must not be moved, so that a
perfect swimming of the cable in the water is maintained) Avoid di-
rect exposure to the sun all the time!
• Before using, please read the instruction for fault rectification thor-
oughly.
• Keep the cleaner always on the handgrip to remove it in and out of
the pool.
Trouble Shooting
Symptom Possible reason
The pool
turns while cleaning
the water (note, this
is normal).
Obstruction in pool.
Cable twists or
coils up.
The cable in the wa-
ter is too long.
The cleaner does
Connecting cable is
not reach all pool
not long enough.
area.
Page 8 of 50
time. Fi-
side. Figure 30
side. Figure 32
side. Figure 33
bag. Figure 36
Corrective action
cleaner
Unplug power
complete the cable
and unscrew.
Remove obstruction in
pool.
Get the excess part of
the cable from the
water. The cable in the
water has to be long
enough to allow the
cleaner to reach all
corners of the bath.
Allow the cleaner to
reach all corners of the
bathroom, enter
maximum length of the
connecting cable into
The cleaner does
not work.
The cleaner does
not clean optimal.
Service processing
Please do not send the unit unauthorized to us, but you should first
contact our service center!
If the product needs to be picked up, so it is necessary to pack it
line,
safely and enclose the invoice (copy) and a copy of the warranty
card.
Once the unit has been returned to us, it will be checked for defects
and repaired of our complaints department. After completing this
work, your device will be returned to you as quickly as possible.
If the submission to guarantee isn't justified, then the costs incurred
will be charged.
The Warranty/Guarantee
VertriebsgmbH. The item will be repaired by the company Steinbach
VertriebsgmbH, because there exist no right of return, the pool
cleaner will not be taken back.
Steinbach VertriebsgmbH,
Aistingerstrasse 2, 4311 Schwertberg, Österreich
the
e-mail: service@steinbach.at
www.steinbach.at
the pool, but consider
a
minimum distance of
the control unit to the
pool.
Slide the pool cleaner
The pool shape
by hand to the places
doesn't make a
where was not cleaned
complete cleaning
and restart manually
possible.
backwards forwards
The water cycle of
Turn
the bath is switched
pump.
on.
Too much air in the Turn off the machine
case. and let all the air
escape.
A foreign object is Contact
in/at drive. center.
Cleaner kicking up
dirt and does not
clean enough.
Turn the two water jets
to 180 °. This reduces
the speed and the
purification
improved.
runs on the company
Poolrunner | 2016_V1
corresponding
off the filter
the service
is
Steinbach