Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2.6
LED INDICATION
The LED lights are permanently active only from 8 a.m.
.
till 8 p.m. (day mode)
From 8 p.m. till 8 a.m., the LED is off (night mode). It
lights up briefly only in case of a program or user change
and when an error condition is signalled (LED flashes red
).
for 1 minute
Check of status of the heater using the LED lights is
performed by briefly pressing any button on the Wifi
.
box
LED indication of heating
▪
Not lit: the panel is switched off
▪
Red: the panel is on and heats
▪
Green: heated - the panel is on, but does not
heat
▪
Orange: Timer mode has been activated
LED indication of RF communication
▪
Green: RF pairing mode
▪
Green-flashing: RF communication runs
▪
Orange-flashing: no connection to V26 >2h
▪
Red-flashing: no connection with RF sensor
>2h
LED indication of Wifi status
▪
Blue-flashing: local mode started
▪
Purple: connected to Wifi router, waiting for
connection with user account on cloud
▪
Blue: connection with online account active
▪ Red-flashing: no connection with Wifi router
3.0
USE OF GS WIFI RADIANT PANELS
3.1
FENIX TFT WIFI APPLICATION
Full control of the panel is possible only through the
«FENIX TFT Wifi» application. Use of the application
requires creation of the user account on the cloud server
From the mobile application, the panel can be turned on
and off, operating modes can be switched and their
parameters modified. The following modes are available:
for heating NO-FREEZE, MANUAL, PROGRAM and spe-
cial modes TIMER and HOLIDAY
3.2
MODES FOR HEATING
ANTI-FREEZING TEMPERATURE
It is a frost protection mode, the panel maintains
the temperature of 7°C in the room. The pre-set
temperature value cannot be adjusted / modi-
fied.
.
.
2.7
ON/OFF SOUND INDICATION
Switching the panel on/off has a sound signal
▪
Two short tones when ON
▪
One long tone when OFF
If the panel is turned on/off by the ON/OFF button directly
on the Wifi box, it can be turned off/on again from the
.
mobile application
2.8
RESET OF SETTINGS
Wifi reset
This procedure only resets Wifi settings (deletion of SSID
and network password
▪ Press buttons ON/OFF+ Wifi for 15s
▪
Wifi LED starts flashing red and blue alternate-
ly, after releasing the button it starts flashing
only blue - local mode has been started
Factory reset
In case of factory reset of the panel, Wifi settings will be
reset (deletion of SSID and network password), all paired
RF devices including the RF sensor will be removed, and
all programs and user-edited constants will be deleted
▪ Press buttons ON/OFF+ Timer for 15s
▪
All LEDs will flash with alternating colours
Note: After the reset, the corresponding panel
has to be removed also from the mobile applica-
tion and new pairing (as during the first start) has
to be done
MANUAL
Panel in the room maintains the set temperature perma-
nently. User intervention is required to change the tem-
.
perature/mode
▪
21°C
Default value:
▪
Adjustable value
PROGRAM
The weekly program, i.e. the panel heats according to the
created program
▪
Every day can have 8 temperature changes
▪
Each temperature change can be assigned any
value ranging 5-35°C (0.5°C step
▪
The program can be created separately for
each individual day, for a block of days/
weekends (5+2 days), or for the whole week (7
days)
▪
Created programs can be copied to other pan-
els in the application
24
):
: 10 °C to 30 °C
)
.
Werbung
