Assembly; Clothing; Operating The Tiller - Texas A/S Fusion 10TG Bedienungsanleitung

Ensure a stable foothold and always keep a firm
hold on the handles. Always walk, never run.
Do not operate the equipment when barefoot or
wearing sandals.
Exercise extreme caution when changing direction
on slopes
By rear tillers, ensure that the blades are protected
by safety shield, only the part of the blades that
works into the soil must be free.
Never attempt to make any adjustments, while the
engine is running.
Use extreme caution when reversing or pulling the
machine backwards
Never operate the engine indoor or in areas with
low ventilation. The exhaustion from the engine
contains carbon monoxide. Failure to observe
could result in permanent injury or death.
Gasoline safety
Use extreme care in handling gasoline. Gasoline is
extremely flammable and the fumes are explosive.
Serious personal injury can occur, when gasoline is
spilled on yourself or your clothes. Rinse your skin
and change clothes immediately!
Use only an approved gasoline container. Do not
use soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other
sources of ignition.
Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 2.5 cm below
bottom of filler in order to provide space for fuel to
expansion.
After refueling, ensure that the cap tighten
securely.
Never use the lock-function on the gasoline gun,
when refueling.
Do not smoke while refueling.
Never refuel inside a building or where gasoline
fumes may get in contact with an ignition source.
Keep gasoline and engine away from appliance,
pilot lights, barbecues, electric appliances, power
tools, etc.
If the fuel tank has to be drained, this shall be done
outdoors
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when
changing tools and when being transported by
means other than under its own power.
Check regularly that all bolts and nuts are
tightened. Retighten if necessary.
The engine must be completely cooled before
storing indoors or covered.
If the machine unused for a period of time, please
refer to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is
no longer applied.
Replace faulty silencers.
Miscellaneous
The gears are delivered pre-greased. However,
always ensure they are well greased before each
use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or
exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Reduce the throttle during engine shutdown and
close the fuel tap, if this exists on the engine.

Assembly

Please follow the steps in figure:
(Actual model may vary from the illustration shown.)
1. Box content
A. Tiller
B. Clutch handle
C. Gear rod
D. Depth skid
E. Support wheels and rear console
F. Lower handletube and upper handlebar
G. Blade guards
H. Throttle control
I. Middle- and outer tiller blades
J. Handle for turning the handlebar
2. Mount rear console, support wheels and depth skid
with the supplied cotter bolts and pins.
3. First, mount the lower handle tube. Use the
supplied mountings and bolts. Be careful not to
overtighten, so the bracket bend.
Then fit the upper handlebar. Use the supplied
assembly kit as shown. Do not overtight bolts.
4. Fit the plastic cover to the upper handlebar with the
supplied bolts and plastic plugs.
5. Mount clutch handle, throttle control and the handle
for turning the handlebar as shown in the picture.
6. Attach the gear rod as shown in the picture.
Tight the counter-nut, so the gear rod is properly
attached.
7. Mount the blade guards using the bolts and nuts
supplied. Note the blade guards has to go under
the body frame.
8. Attach the bumper using the bolts and nuts
supplied.
9. Mount the middle- and outer tiller blades using the
cotter bolts and pins.
Fill the motor with oil.
See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work
clothes, hard-wearing work gloves, ear defenders and
non-slip boots with steel toecaps.

Operating the tiller

Ensure the machine is placed on a level surface
with the support wheels lowered prior to start.
14