Lubrication Of Gearbox; Starting And Stopping The Engine; Accessories Overview - Texas A/S Fusion 10TG Bedienungsanleitung

from the rod (C) to lock the wheel assembly into
position.
Adjustment of depth skid
The depth skid can be set to 3 different depths. The
deeper it extends into the soil, the deeper the tilling
blades will work and the slower the machine will
advance. Setting the correct tilling depth will
significantly reduce the effort required. The depth skid
should always be adjusted to suit the ground conditions.
We recommend testing several depths to see which
works best.

Lubrication of gearbox

The gearbox is filled with gear oil at the factory.
Check oil level (the oil level should be visible for the
eyes, when the oil cap is removed - Fig. 17) and fill up
with gear oil after the first 20 and 50 working hours.
Fill with gear oil type GL-5 / SAE 80W/90.
Do not overfill with oil.
For every 100 working hours, the gear oil must be
replaced. Remove the drain plug (Fig. 18) and let the oil
run out into a plastic tub or similar.
Tip: It is recommended to let the tiller blades rotate for
a while before draining the gearbox. It will make the
gear oil warm, so it runs out easier.
Fill with new gear oil (about 1.2 - 1.3 liter)

Starting and stopping the engine

Remember: Always check the oil level prior to use!
The oil level must reach the edge of the filling hole
(Fig. 21). Always use SAE-30 oil. Use only unleaded 95
octane gas. Never over-fill the gas tank.
Warning: Stay out of dashed zone, while starting the
engine!
Always start the engine from dotted operation zone See
red color in Fig. 20 .
Starting the engine
1. Set the throttle control on the handle to "4"
(Fig. 13B)
2. Open the fuel tap, if engine is fitted with this.
3. Position the choke at max.
The choke is not required if the motor is hot.
4. Pull the start cord to start the motor. Always feed
the start cord back into the motor by hand.
5. When the motor is started, set the choke to
minimum.
Stopping the engine
1. Set the throttle control to "1" and let the motor run
for approx. 30 seconds.
2. When the motor idles, set the throttle control to
"Stop".
Vibrations may travel up into the handle
during use. We therefore recommend taking
a break every 2 hours.

Accessories overview

Several accessory options are available for FUSION 10.
See Fig. 22 on page 5.
Texas recommend buying accessories, as it increases
the usage possibilities of the machine considerably.
Below accessories can be purchased for use with
FUSION 10 (the list is subject to local
changes/availabilities):
Tilbehør
Wheels: used to mount accessories, such as
rake.
Art. no. 91075500100
Digging claws: used if the soil is loose or
muddy and the machine is to be operated with
a ridge plough or harrow instead of wheels.
Art. no. 91075300100
Side discs: used for tilling in between crops,
such as carrots/potatoes, to avoid covering the
crops in soil. Side guards can also be used for
tilling along a wall or stone path, or in soft soil.
Art. no. 91075700100
Weight blocks: used to give the machine a
better grip when operating with a trailer or
snow blade.
Art. no. 91075400100
Rake: used to rake paths and entrances with
loose stones, for instance pebbles.
Art. no. 91062500100
Harrow: used to loosen the soil between crops
and thus remove weeds.
Art no. 91070000100
Weeder: used to loosen the soil and thus
remove weeds on paths and entrances.
Vare nr. 91061500100
Scarifier: used to aerate the lawn and remove
underlying dead grass from the lawn. The
grass grows greener and stronger, which
prevents the grown of moss.
Art. no. 91051550100
Potato plough: used for harvesting potatoes
Art. no. 91061200100
Trailer with seat: used for transport of various
materials.
Art. no. 91075000100
Assembly plate: used to attach front mounted
accessories.
Art. no. 91075600100
Snow blade: used to scrape snow from a solid
surface, such as paving slabs. Can be tilted to
the left/right. The assembly plate is necessary
for fitting.
Art. no. 92000160100 + 91075600100
Ridger: used to plough up ground for
potatoes, carrots and other root crops.
Art. no. 91076100100
Plough: used to turn the soil.
Art. no. 91076000100
Turning plough: used to turn the soil. Can be
rotated 180 o .
Art. no. 91076200100
Rain-cover: used to protect the machine from
dirt or rain during storage.
Art. no. 40-11720
16
Nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16