DeWalt XR LI-ION DCD991 Bersetzung Der Originalanweisungen Seite 23

Speed selector
8
Worklight
9
Worklight switch
10
Belt hook (Optional accessory)
11
Mounting screw
12
Bit holder (Optional accessory)
13
Side handle
14
Main handle
15
Date code position
16
Fuel gauge button
17
Low mode
18
Medium mode
19
Spotlight mode
20
Intended Use
These hammerdrills are designed for professional drilling,
percussion drilling and screwdriving applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or mental
abilities; lack of experience, knowledge or skills unless they are
supervised by a person responsible for their safety. Children
should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack from the
Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the battery release button
pack out of the tool handle.
2. Insert battery pack into the charger.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge, which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 17 . A combination of the three green LED lights will
illuminate, designating the level of charge left. When the level
WALT batteries and chargers.
is fully charged.
1
2 and firmly pull the battery
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook and Magnetic Bit Holder (Fig. A)
Optional Accessories

WARNING: To reduce the risk of serious personal injury,
ONLY use the tool's belt hook to hang the tool from a work
belt. DO NOT use the belt hook for tethering or securing the tool
to a person or object during use. DO NOT suspend tool overhead
or suspend objects from the belt hook.

WARNING: To reduce the risk of serious personal injury,
ensure the screw holding the belt hook is secure.

CAUTION: To reduce the risk of personal injury or
damage, DO NOT use the belt hook to hang the drill while
using as a spotlight.
IMPORTanT: When attaching or replacing the belt hook
magnetic bit holder 13 , use only the mounting screw
is provided. Be sure to securely tighten the screw.
The belt hook and magnetic bit holder can be attached to either
side of the tool using only the screw provided, to accommodate
left- or right-handed users. If the hook or magnetic bit holder is
not desired at all, it can be removed from the tool.
To move belt hook or magnetic bit holder, remove the screw
that holds it in place, then reassemble on the opposite side. Be
sure to securely tighten the screw.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the variable speed
trigger switch 3 . To turn the tool off, release the trigger switch.
Your tool is equipped with a brake. The chuck will stop as soon
as the trigger switch is fully released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Side Handle (Fig. A, I)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed. Failure to
do so may result in the side handle slipping during tool operation
and subsequent loss of control. Hold tool with both hands to
maximize control.
The side handle 14 clamps to the front of the gear case and
may be rotated 360˚ to permit right- or left-hand use. Side
handle must be tightened sufficiently to resist the twisting
action of the tool if the accessory binds or stalls. Be sure to grip
the side handle at the far end to control the tool during a stall.
If model is not equipped with side handle, grip drill with one
hand on the handle and one hand on the battery pack.
nOTE: Side handle comes equipped on all models.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the for ward/re verse control button on the right side of
the tool.
EnGLIsH
11
12 that
4 determines the direction of
or
23