EINHELL FREELEXO LCD BT Originalbetriebsanleitung Seite 39

Description of the control panel with LCD
display (Fig. 9a)
50. LCD
51. POWER button
52. "START" button
53. "HOME" button
54. "OK" button
55. Back button
56. Navigation buttons
57. Numeric keypad
6.3 Cutting height adjustment facility
Important! Adjust the cutting height only when
the robot lawn mower has been switched off . Do
this by pressing the STOP button (3). The cutting
height adjustment facility (4) allows the cutting
height of the robot lawn mower to be set to infi ni-
tely adjustable settings between 20 and 60 mm,
which can be viewed on the scale.
If the grass is taller than 60 mm it has to be shor-
tened to a maximum of 60 mm fi rst to avoid expo-
sing the robot lawn mower to excessive load and
adversely aff ecting its operating effi ciency. Use a
conventional lawn mower or trimmer to do this.
After installation has been completed, the cutting
height can be adjusted using the cutting height
adjustment facility (4). Always start with a higher
cutting height and reduce it in small steps until
you reach the desired height.
6.4 Locking mechanism / PIN
The locking mechanism prevents the unautho-
rized use of the robot lawn mower without a valid
code. You have to enter a personal four-digit secu-
rity code for this.
Lock release
Before you start using the robot lawn mower,
you have to enter the correct PIN (standard PIN:
"1-2-3-4").
Standard PIN: New PIN:
1 2 3 4 _ _ _ _
Changing the PIN
To change the PIN, proceed as follows.
1. In the main menu of the LCD display (50), use
the navigation buttons (56) to navigate to the
"Change PIN" tab and confi rm the entry with
the "OK" button (54).
2. First, enter the current PIN (standard PIN:
1-2-3-4) using the numeric keypad (57).
3. Then use the numeric keypad (57) to enter
your personal PIN.
Anl_FREELEXO_LCD_BT_SPK13.indb 39 Anl_FREELEXO_LCD_BT_SPK13.indb 39
GB
4. After this, confi rm the settings you have made
by pressing the "OK" button (54).
5. Confi rm the message "Save changes?" with
the "OK" button (54) or press the Back button
(55) to discard the change.
6. Important! Make a note of the new PIN.
Requesting your PIN if you lose it
Have the receipt and the serial number of the
robot lawn mower ready. You need them in order
to get your PIN.
1. Connect a USB stick to the USB connection
as shown in the illustration (Fig. 11).
2. Switch on the main switch (7)(ON).
3. Press the POWER button (51) and the "OK"
button (54) at the same time. The robot lawn
mower will now start in boot mode.
4. Press the 1 key on the numeric keypad (57).
5. Pull out the USB stick. Import the data from
the USB stick to a computer. A text fi le (*.txt)
will have been created by the robot lawn
mower. This fi le contains a PUK, a personal
code. Please contact the customer services
team to obtain your PIN.
6.5 Settings of the robot lawn mower
The main menu of the LCD display (50) shows
you the current date and time setting of the robot
lawn mower, as well as the current charge sta-
tus. You can choose between the tab options of
"General settings", "Mowing time settings" and
"Change PIN". Using the navigation buttons (56),
move the display to the tab you require and con-
fi rm the entry with the "OK" button (54). Press the
Back button (55) in order to exit the respective
menu.
General settings
•
Time settings
Using the navigation buttons (56), go to the
point that you wish to change and enter the
figure you require using the numeric keypad
(57). After this, confirm the settings you have
made by pressing the "OK" button (54). Con-
firm the message "Save changes?" with the
"OK" button (54) or press the back button (55)
to discard the change.
It is recommended to base the mowing time
setting on 8 hours per day for 500 m² as a
guideline. The selected working time may
need to be adapted to take account of the
garden's size and complexity.
•
Mowing in the rain
The rain sensor (5) can be programmed using
this setting. The default factory setting for the
- 39 -
16.11.2023 10:09:18 16.11.2023 10:09:18