KIKKA BOO i-FELIX Gebrauchsanweisung Seite 12

IMPORTANT! KEEP FOR FUTURE REFERENCE!
EN
READ CAREFULLY!
I. PARTS
1. Headrest; 2. 3-point safety belt guide; 3. Shoulder strap guide; 4. Shoulder straps; 5. Seat cushion 6. Shoulder pad; 7. Buckle; 8. Shoulder strap adjusting belt; 9. Base; 10. Adjusting
button for rotation; 11. Adjusting lever for rotation; 12. Reclining adjuster; 13. Crotch pad; 14. Backrest; 15. Side protector (3 options); 16. Headrest adjusting lever; 17. Top tether; 18.
Connective band of strap sleeve; 19. Shoulder straps; 20. Harness strap hook; 21. Shoulder straps adjusting belt; 22. ISOFIX release button; 23. ISOFIX locking display window;
II. OPTIONS FOR SIDE PROTECTORS
2.1 Base with rotate button.
2.2 Base with rotate handle.
2.3 Without side preotectors.
III. USAGE METHOD
3.1 Adjust the headrest: Depending on the height of the child , the head is adjusted in 12 positions. As shown, adjust the headrest to the appropriate height by adjusting the red headrest
lever up and down.
Important: after loosening the headrest by adjusting the red lever, check that the headrest is locked in a safe and suitable position by pulling up or down the headrest.
3.2 Check the height of the straps: Check that the height of the shoulder strap is suitable for your child: straps should pass through the strap holes that are equal to the child' s shoulder
or slightly higher than the child' s shoulder position.
The height of the shoulder strap of this product can be adjusted up and down together with the headrest. When using, adjust the height of the headrest to adjust the shoulder strap to
the suitable height.
3.3 Buckle using - Step 1: Connect two buckle tongues.
3.4 Buckle using - Step 2: Insert them together into the buckle. If you hear "click", it means that the buckle is locked. Pull up the buckle tongues, and check that the buckle is locked
tightly.
3.5 Buckle using - Step 3: To unlock the shoulder strap, press the red button and separate the two buckle tongues.
3.6 Adjust the length of the straps - Tighten the straps:
Pull the straps outward until the straps are completely tightened. Tighten the straps as much as possible without causing discomfort to the child. The lap belt is as low as possible and
should be located near the crotch rather than the abdomen.
WARNING!
Loosen straps are dangerous. So every time the child is placed in the child safety seat, check that the seat belt silver adjuster can be used normally, and then pull the
straps, tighten the straps, and do not twist the straps.
3.7 Adjust the length of the straps - Loosen the straps:
The shoulder strap can be loosened by pressing the silver adjuster (hidden under the cover of the seat).
Action: press the silver adjuster down while the other hand holds the two straps to the right front of the child to loosen the straps.
3.8 Adjust ISOFIX
Press the red ISOFIX release button and push the ISOFIX out to the outermost so that the ISOFIX can be installed.
If you want to retract the ISOFIX, you can pull the ISOFIX back by pressing the red ISOFIX release button.
3.9 Installation of child safety seat
Step 1: first pull the ISOFIX to the outermost end, then insert the ISOFIX to the anchor on your car. When you hear "click", it indictates that the ISOFIX is totally locked. Note: At this time,
the ISOFIX lock display window appears green.
Step 2: Push the seat against the back of the car until the two are perfectly tightly aligned. If you want to release the ISOFIX chuck, you can unlock the ISOFIX chuck by pressing the red
release button of it.
Step 3: Use a 3-point safety belt to install the child safety seat.
3.10-3.11 Adjust the angle of the child safety seat
The seat angle can be adjusted by pressing the red angle adjusting lever. It is convenient to adjust the suitable angle and increase comfort when using.
3.12-3.13 Rotating adjustment of the child car seat
Note: There are two optional bases for this product. One is the base with an adjusting lever, the other one is with a button.
Option 1: Base with an adjusting lever: As show in the figure, pull the red adjusting lever to rotate the child car seat in 360°.
Option 2: Base with a button. As shown in the figure, press the red button to rotate the child car seat in 360°.
IV. INSTALLATION AND USE OF THE CHILD SAFETY SEAT
4.1-4.3 Installation of the child safety seat (height 40-105cm)
This product is suitable for children in height 40-105cm, Rearward facing installation.
Step 1: First adjust the seat to the most inclined gear, and then rotate the seat body 180 degrees on the car seat.
Step 2: Secure the seat to the car seat with ISOFIX, make sure the ISOFIX is locked, the display window appears green, and then slowly push the seat onto the back of the car seat until it
fits completely.
Step 3: Loosen the buckle and shoulder strap, put the child in the child's seat, and then buckle and pull the shoulder strap. Check the shoulder strap and head height. Note: all seat belts
should not be twisted.
Step 4: Use the adjusting buckle on the top tether to adjust the top tether to the appropriate length. The top tether of the seat is passed through the side of the head of the seat. The top
tether is attached to the corresponding hook on the car (the attachment point suggested in the manufacturer's manual), finally tighten the top tether when the top tether is secured, its
regulator is shown as green.
4.4 - 4.5 Installation of the child safety seat (height 76-105cm)
This product is suitable for children in height 76-105cm, Forward installation
Step 1: Use ISOFIX to secure the seat to the car seat, make sure the ISOFIX is locked, the display window appears green, and then push the seat slowly to the back of the car seat until fully
ENGLISH