MHZ SOLIX FIX Montage- Und Bedienungsanleitung Seite 48

Solix Fix exterior roller blinds
Adjustment instructions
3.6 Deleting the end positions
DE
1. When using hand-held radio transmitters, remove the cover on the back to make
your adjustments.
Caution: Press down gently on the battery to keep it in place
(making contact).
After making your adjustments, slide the cover back on.
2. Press the P2 button on the radio transmitter once
=> The roller blind confirms this button press by beeping +
moving briefly once.
3. Press the DOWN button on the radio transmitter once
=> The roller blind confirms this button press by beeping +
moving briefly once.
4. Press the P2 button on the radio transmitter once
=> The roller blind confirms this button press by beeping +
moving briefly four times.
FR
3.7 Unpairing a radio transmitter
i a: radio transmitter that will remain paired
b: radio transmitter that will be unpaired
1. When using hand-held radio transmitters, remove the cover on the back to make
your adjustments.
Caution: Press down gently on the battery to keep it in place
(making contact).
After making your adjustments, slide the cover back on.
2. Press the P2 button on radio transmitter a once
=> The roller blind confirms this button press by beeping +
moving briefly once.
3. Press the P2 button on radio transmitter a once
=> The roller blind confirms this button press by beeping +
moving briefly once.
NL
4. Press the P2 button on radio transmitter b once
=> The roller blind confirms this button press by beeping +
moving briefly five times.
Radio transmitter b has now been unpaired.
3.8 Resetting to factory settings using a taught-in radio remote
control
Deletes all settings and all taught-in radio transmitters
1. When using hand-held radio transmitters, remove the cover on the back to make
your adjustments.
Caution: Press down gently on the battery to keep it in place
EN
(making contact).
After making your adjustments, slide the cover back on.
2. Press the P2 button on the radio transmitter once
=> The roller blind confirms this button press by beeping +
moving briefly once.
3. Press the STOP button on the radio transmitter once
=> The roller blind confirms this button press by beeping +
moving briefly once.
4. Press the P2 button on the radio transmitter once
=> The roller blind confirms this button press by beeping +
moving briefly five times.
ES
48
IT
3.9 Resetting to factory settings without a radio remote control
Deletes all settings and all taught-in radio transmitters
1. Press and hold the setting button on the drive
=> The roller blind confirms this button press by
moving briefly four times at intervals of approx. 4
P2
seconds + beeping four times when the setting
button is released.
=> To reprogram, see step 3.1.
A setting button
B emergency charging socket for charging the battery
3.10 Limiting the number of channels
(
only applies to 15-channel radio transmitters)
P2
These settings can be used to limit the radio transmitter to how many channels
i
are actually needed to control the drives. Select channel 0 to control all blinds.
1. Press the P1- and P1+ buttons on the
radio transmitter simultaneously
=> "C" appears on the LCD display unit.
a
2. Press and hold the P1- and P1+ buttons on the
radio transmitter
P2
=> "15" appears on the LCD display unit.
a
P2 P2
3. Press the P1- or P1+ button on the radio transmitter
b
to select the number of channels. If you will only
control two drives with this radio transmitter, for
P2 P2
example, select "2".
+
4. Press the STOP button on the radio transmitter once
=> " " appears on the LCD display unit.
b b
a a
5. "2" will appear after a short time to indicate that the
channels are limited to two.
P2
i If you want to deactivate the "Limit number of channels" extra function, repeat
steps 1 to 5, increasing the number you select in step 3 to "15".
P2
A
B
P1+
C
C
P1–
P1– P1+
15
15
2
2
P1– P1+
2
2
Edition 08/2021
Subject to technical changes I