Horizon Hobby parkzone Stinson Reliant SR-10 BNF/PNP Bedienungsanleitung Seite 19

Troubleshooting Guide
Problem
• Aircraft will not respond to throttle
but responds to other controls
• Extra propeller noise or extra
vibration
• Reduced flight time or aircraft
underpowered
• LED on receiver flashes and aircraft
cannot be controlled by transmitter
• Control surface does not move, or is
slow to respond to control inputs.
• Controls reversed
• Motor loses power
• Motor power pulses then motor
loses power
Replacement Parts and Optional Parts
Number Description
PKZ4428 Motor Mount w/Screws
PKZ1012 Propeller, 9.5 x 7.5
PKZ4416 480 Brushless Outrunner Motor, 960Kv
PKZ1031 11.1V 1800mAh LiPo Battery
EFLA1030 30-Amp Pro Switch-Mode BEC Brushless
ESC
PKZ5201 Spinner Nut And Propeller Adapter
PKZ5202 Decal Sheet
PKZ5203 Main Landing Gear with fairing & Wheel
Pants
PKZ5204 Tail Wheel
PKZ5205 Pushrod Set with Clevis
PKZ5206 Horizontal Stab with Access
PKZ5207 Painted Cowl
PKZ5209 Belly Cover and Battery Hatch
PKZ5210 Wing Struts & Mount Screw/(4)Pins
PKZ5211 Wheel Pants With Screws
PKZ5212 Flap Hardware set (No Servo Included)
PKZ5220 Painted Bare Wing
Possible Cause
• Throttle not at idle at control setup so
throttle not armed
• Throttle channel is reversed
• Damaged propeller, motor or motor mount
• Loose propeller and propeller adapter
• Propeller installed backwards
• Flight battery charge is low
• Propeller installed backwards
• Flight battery damaged
• Less than a five (5) second wait after
powering transmitter and before connecting
flight battery to aircraft
• Transmitter too close to aircraft during
binding process
• Transmitter bound to another aircraft
• Batteries in transmitter low
• Control surface, control horn, linkage or
servo damage
• Wire damaged or connections loose
• Parts not secured in fuselage
• Transmitter settings reversed
• Damage to motor, or power components
• ESC uses default soft Low Voltage Cutoff
(LVC)
Number
PKZ5267
TES4714
EFLA110
EFLA253
EFLA258
EFLAEC301
EFLAEC302
EFLAEC303
EFLC505
SPMAR500
SPMAR6200
SPMR5500
SPMR6600
SPMR7700
Solution
• Bind with throttle stick and throttle trim
at lowest setting
• Reverse throttle channel on transmitter
• Replace damaged parts
• Tighten parts for propeller and adapter
• Remove and install propeller correctly
• Completely recharge flight battery
• Remove and install propeller correctly
• Replace flight battery and obey flight
battery instructions
• Disconnect then connect flight battery to
aircraft
• Move powered transmitter a few feet
from aircraft, disconnect and connect
flight battery
• Bind transmitter to receiver
• Replace transmitter batteries
• Replace or repair damaged parts and
adjust controls
• Do a check of wires and connections,
connect or replace as needed
• Make hook and loop fastenings tight so
no parts move in fuselage
• Do the Control Direction Test and adjust
controls on transmitter appropriately
• Do a check of batteries, transmitter,
receiver, ESC, motor and wiring for
damage (replace as needed)
• Recharge or replace flight battery
Description
Painted Bare Fuselage
Red Touch-up Paint (optional)
Power Meter (optional)
Hex Driver, 1.5mm (optional)
Screwdriver, #1 Phillips (optional)
EC3 Device Connector, Male (2) (optional)
EC3 Device Connector, Female (2)
(optional)
EC3 Device/Battery Connector, Male/
Female (optional)
1- to 5-Cell Li-Po Battery Charger w/
Balancer (optional)
DSM2 5-Channel Sport Receiver (optional)
DSM2 6-Channel Sport Receiver (optional)
DX5e 5-Channel Transmitter Only
(optional)
DX6i 6-Channel Transmitter Only
(optional)
DX7 7-Channel Transmitter Only (optional)
EN
19