Werbung
Verfügbare Sprachen
Verfügbare Sprachen
decoupled:
the upper inputs have a very high amplification
a low output voltage), the lower inputs have a low amplification (for instruments
with a high output voltage).
Left hand input
(1)
The left hand input jacks are for the effects channel with mixable
and vibrato. The connection
cable coming out from the spring reverb. system (29)
must be plugged
into the jack REVERB (25) at the rear of the amplifier.
Right hand input
(2)
The right hand input jacks are for the regular
brato).
E) Switdling
on
The amplifier
is being switched
on with the lever swiWt
(20) above the switch is lighting
up; the amplifier
F) Adjustment
and operation
The volume
for both
&lannels
is adjusted
sound impression
is set with the bass, mid-range,
particulars
of the room.
The controls
(3), (4), (6) and (9) affect the right hand input jacks (regular channel),
the controls
(10), (II),
(13), (15), (17), (18) and (19) affect the left hand input
The boost switches located above the tone controls permit pre-emphasizing
respective
frequency
range.
Bass boost swiW1 (5) and (12)
(push
to the right
for ON)
This switch permits
a frequency
correction
range is being pre-emphasized
herewith at 50 c.p.s., and the lower frequency
is being
extended
considerably.
This
richer
sound.
Mid-range
boost swiW1 (7) and (14)
(push to the right for ON)
This switch permits a frequency
correction
Treble boost swiW1 (8) and (16)
(push
to the right
for ON)
This
switch
permits
a frequency
correction
that the frequency
range is being pre-emphasized
overtones
of a guitar are being emphasized
Reverberation
The control
REVERB
(17) permits
to mix the effects
12
(for instruments
with
reverberation
(without
reverb. and vi-
ON (21). The pilot lamp
is ready for operation.
with the controls
VOLUME.
The desired
and treble control
to suit the
of the
of + 9 dB at 50 c.p.s. The frequency
limit
means
that the bass
instrument
gives
a far
of + 10 dB at 500 c.p.s.
of +
10 dB at 5 kc.p.s.
This
means
at 5 kc.p.s. and that the
especially.
channel
with reverberation.
The
controls
INTENSITY
(18) and SPEED
with vibrato.
To turn of the vibrato
turn the control
hand
stop.
G) Remote control connection
A foot-operated
remote control swit&l
for switdling
on/off the reverberation
The telephone-type
plug must
be inserted
H)
Service
and
Maintenance
DYNACORD units are quality
products
component
parts we use are first-class
Sive and strict
inspection
of the goods
of the various components.
If it should happen nevertheless
(tube, capacitor,
etc.) becomes defective
apply to the nearest DYNACORD service shop.
Remember
that the unit inclusive
of the control
stances
be cleaned
with
agents
dissolving
recommend
to use a rag moistened
with soapy water for cleaning.
(19) permit
to mix the
effects
channel
INTENSITY
fully to its left
can be connected
to jack T. R. PEDAL (28)
or vibrato effect.
into the jack to full stop.
and belong to the world's
top class. The
products
of leading manufactures.
Exten-
received
ensure
perfect
and uniform
quality
that a component
part
causing the unit to break down, please
panel must under
no circum-
plastics
(nitro
dilutions,
etc.). We
13
Werbung
