LGB RhB Tm 2/2 21 20413 Bedienungsanleitung Seite 8

Youcan program the following registers:
Register Function
CVI
LOCO address
CV2 Starting voltage
voltage for speed settingI - if locostartsonlya higher
s settin increase value.
CV3 Acceleration I = fast, 255 = slow
CV4 Braki 1 -fast 255 = slow
CV5
Max. voltage
Voltagefor highest speedstep - if a lower top speed is
desired decrease value.
CV5 after input of CV6 (when programming with Older55015)
function value forCVtobe r rammed
CV6 CV to be ro rammed when rammin with older 55015
CV29 NMRA configuration
Bit programming
Bit I: direction, O normal, I reversed[01
Bit 2: speed steps, O= 14 (LGB), 2 = 28 [01
Bit 3: analogoperation, O= not possible, 4 = possible [41
Bit 4: not used [01
Bit 5: speed steps, O factory-programmed.
16 = user-programmed[O]
Bit 6: address area,O= 0-127 (LGB),32 128-10239 [01
Toprogram, add the valuesfor the individual Bits and
program the resulting function value.
Hint: Toprogram a loco to reversed direction of travel (for
example, F7 A-B-Acombination), program function value 5.
Attention! Loco addresses 128-10239and 28 speed steps
cannot be used with LGB MTS .
CV49 Voltage for function terminal Fl
(depends on loco model, do not change, as functions can
be attected or dest d
CV50
Volta for Ii Min terminals see CV49
CV51 Command for function terminal Fl
O= lighting button 9
I = button I (buttons 2-8 not used)
9 = button 1 (buttons 2-8 usedas well)
10 button 2
11 = button 3
12 button 4
13 = button 5
14 = button 6
15 = button 7
16 = button 8
64 = lighting button 9 (on only when loco is reversing)
65 = button I (on only whenloco is reversing)
128 = lighting button9 (on only Whenloco is movingforward)
129= button1 (on onlywhenlocois moving forward)
14
(dependson loco model,do not change,as functions can be
affected or destr
Available Factory CV52 Command for front li
CV53
values Command for rear I
CV54 LGB configuration
00-22 3
(0-255) 12] Bit programming
Bit1: tund-offfunction,o =off, 1 -on (01
Bit 2: MTS Back-EMF. O = off,
1-255 3 Bit3: analog Back-EMF, O off, 4 on [01
1-255 3 Bit 4: not used [01
Bit5: Fl constant, 1 6 -Fl flashing(01
(1-255) 12551
Bit 6: O= F2constant, 32
Bit 7: sound function (0 or 64) [0]
Bit 8: sound function (Oor 128) [OJ
To program, add the valuesfor the individual Bits and
program the resulting function value.
The valuesfor Bits 5-8 vary betweenlocos. The valuesfor
your loco can be read using the 55045 MTS PCDecoder
Programming Module.
Hand-off function on: When operatingwith 55015, you can
adjust direction and speedfor two seconds after selecting a
movin loco without
CV55 Reset factory pre-set values for CVS
Program:
5-55->
CV56 Voltage tor function terminal F2
(depends on loco model, do not change, as functions can
be affected or d
CV57 Command tor function
CV58 Pause time (analog operation)
(1-32) [32) (0.5 seconds x function value) When the polarity of the
analog
rammed time
CV60
1_32 5 Back-EMF:Max.adjustment factor
Specifiesthe max. increaseor decreaseof voltage applied
during eachtime interval (programmedin CV61),
255 = large steps
The factory pre-set valuesof CV60and CV61are optimized
for LGB motors.
CV61 Back-EMF: A djustment frequency
Specifieshow often per secondthe motor voltage is adjusted-
accordingly,the loco will react to curves and grades
immediatelyor with a short delay
O = immediate ad ustment 255 = maximum dela
CV62 Back-EMF:Max.Adjustment
Limits the total adjustmentin motor voltage.If there is a very
large load on the motor, the adjustment will not exceedthis
value- for more realisticoperations, so that locos will Slowa
bit on grades.O= no adjustment,255
terminal see CV51
Mi terminal see CV51
on [21
F2flashing (0]
causin the loco to
(1-32)
terminal F2 see CV51
(0-255)
voltage is reversed,the loco waits for the pro-
riod then accelerates in the new direction
(1-255)
(0-255)
(0-255)
maximum adjustment
128
[641
132)
[01
[41
[161
[2551
15