Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DecoderProgrammingModule(see
Lubrication n
Instructions for advanced users).
The axlebearings should be lubricat-
These functions also can be pro-
ed occasionally with a small amount
grammed from the 55015 Universal
of LGB MaintenanceOil (50019).
Remote.
Cleaning
Power Supply
This model can be cleanedexternally
Attention! For safety and reliability,
using a mild detergent and gentle
operate this model with LGB power
stream of water. Do not immerse this
supplies (transformers, power packs
model.
and controls) only. The use of non-
LGB power supplies will void your
Replacing the light bulbs n
warranty.
Front upper and rear lights:
Usethis model with LGBpower sup-
Carefullypry the lens awayfrom the
plies with an output of at least I
lantern. Usingtweezers,remove and
amp. For more information on LGB
replacethe bulb. Reassemble.
power supplies for indoor, outdoor
Front lower lights: Pull the lantern
and multi-train operation, see the
housingawayfrom the model.Remove
LGB catalog.
and replacethe bulb. Reassemble.
Cab light: Usingtweezers,remove
Attention! After extended operation,
and replacethe bulb.
this model may leave carbon dust or
other
debris around
the track. This
Replacing the traction tire
dust and debris can stain carpet and
- Under
other
materials.
Consider
this when
screws on eachend Ofthe gearbox.
setting up your layout.Ernst Paul Le-
- Carefullypull the gearbox out of
hmann Patentwerk
and LGB of Ame-
the model.
rica are not liablefor any damages.
- Carefullyunplug the wiring cable.
- Usea small,straight-bladescrew-
driver to replacethe traction tire:
SERVICE
- Pry the old traction tire out of the
wheel groove.
Do-it-yourself
Service
Levels
- Gently insert the newtraction tire
Level
- Beginner
into the wheel groove.
Level
- Intermediate
- Make sure that the traction tire is
Level O - Advanced
seatedproperly in the wheelgroove.
- Reassemble.
Attention! Improper service will void
your warranty. For quality service,
contact your authorizedretaileror an
Maintenance parts
LGB factory service station (see
50010 Smoke and CleaningFluid
Authorized Service).
50019
51020 Gear Lubricant
Hint: Additional expert instructions
63120 Brushes, Assembled,
for many LGB products are available
at www.lgb.com.
63218 StandardPick-Up Shoes,
68511 Plug-in Bulb, Clear,5V,
12
INSTRUCTIONS
USERS
MTS Onboard Decoder
Programming functions
You can program numerous func-
tions of the onboard
your requirements.If you want to do
this, program the 'finction values"
in "registers" (CVS)using a PC and
the 55045 MTS PC DecoderProgra-
mming Module. You can also pro-
gram the function values using a
55015 Universal Remote.
Hints:
- For normal operation, it is not nece-
ssary to changethe function values.
- If programming results in unsatis-
factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
ister
the model,
remove two
This also reprograms the loco
address to the factory pre-set
value.
To reprogram the factory pre-set
function
selectprogrammingmode"P" (dis-
plays shows "P
and 5 and pressthe right arrow but-
ton. The display shows "P
Input 5, 5, and 5 and press the right
arrow button again.
Maintenance
Oil
14 mm and 16 mm,
8 pieces
2 pieces
10 pieces
FOR ADVANCED
decoder to suit
CV55 to function
value
55.
values with
the 55015,
Then input 6, 5,
again:
13
Werbung
