Dik Geurts Bora Corner Installationsvorschrift Seite 42

Make sure everything is mounted level and that the wall bracket is centrally located under the flue exhaust in the
!Caution
ceiling.
Prior to placing the appliance, remove the door in order to avoid damage and make the installation easier.
!Tip
Ø
Break out the cams at the back of the appliance.
Ø
Suspend the appliance from the wall bracket.
Ø
Adjust the appliance by means of the adjustable feet at the rear of the appliance using an open-end wrench, until
the appliance is hanging straight in relation to the wall. (fig. 10-7).
Ø
Place the stove pipe (fig. 10-5/6) around the pre-mounted conical ring. If necessary, place the rosette.
9.7.1.2 Installing the stucco guard plate
If the appliance is placed less than 35 cm from a non combustible wall, we recommend installing the stucco guard
plate supplied with the front models. Without this plate, the stucco or the paint layer can be damaged by high
temperatures (see appendix 2, fig. 20).
Proceed as follows:
Ø
Allow the guard plate at the back of the glue gas duct to rest on the appliance.
Ø
Then press the plate against the flue gas duct.
Ø
Drill 4 holes (Ø 4 mm) and fasten the plate with the supplied screws (see appendix 2, fig. 20).
This plate does not provide protection against combustible materials!
!Caution
9.7.2 Bora Corner, Fixed
9.7.2.1 Placing the appliance
This appliance must be suspended from the ceiling.
The Bora Corner, Fixed may only be mounted on a horizontal, non combustible and robust ceiling.
!CAUTION
When placing the appliance, proceed as follows (see appendix 2, fig. 9, 10, 15, 16 and 17):
Ø
A sliding pipe (0.5 metre long) is supplied with the appliance. Ensure that the pipe starts at the bottom of the
double-walled duct and protrudes approximately 150 mm from the ceiling (fig. 17-5).
Ø
Determine the position of the flue exhaust based on appendix 2, fig. 15). Keep a minimum distance of 402 mm
into account from the appliance to the combustible wall (see A in appendix 2, fig. 16).
The Bora Corner, Fixed can be adjusted to a particular angle. This angle determines the position of the flue
!Tip
exhaust.
For details we would like to refer you to appendix 2, fig. 15).
Ø
Slide the ceiling plate (fig. 15-2) over the sliding pipe against the ceiling and mark out the 8 (recessed) fastening
holes.
Ø
Drill the 8 holes and push the supplied key bushes (fig. 15-1) in the ceiling.
Ø
Attach the ceiling plate (fig. 15-2) to the ceiling with the 8 Allen screws (fig. 15-3).
Ø
Grab the supplied rigid pipe (fig. 15-4) and slide the lock ring (fig. 15-5) from the bottom side carefully around the
rigid pipe.
Use the supplied aerosol with heat-resistant paint to repair possible damages.
!Tip
Ø
Press the lock ring and rigid pipe against the ceiling plate and fasten them with the 8 Allen screws (fig. 15-7).
Ø
Remove the flame baffle plate. See section 9.6.2.
Ø
Place the appliance, using a lift table or scissor jack, under the rigid tube (fig. 16-4) and fasten the appliance with 3
bolts and accompanying rings (fig. 16-2 and 3) to the rigid pipe.
Ø
If applicable, place the flame baffle plate (see appendix 2, fig. 12).
Ø
Adjust the appliance in the required position.
Ø
Screw the 6 small hexagon socket screws (fig. 15-6) against the flange attached to the pipe (fig. 15-4).
9.7.3 Bora Corner, Cube
Observe the following instructions when building the Bora Corner, Cube:
Ø
Stack the 3 cubes on top of one another and fasten them together, in the required orientation, using the supplied
8 bolts and nuts.
When using the bottom connection, the top cube can be placed with the opening to the rear, so that the
!Tip
connection is hidden from view.
Ø
If an outside air connection is used, the plates concerned must be broken out; 6x at a bottom connection and 1x
at a rear connection. (see appendix 2, fig. 18).
Ø
Place the Bora Corner including the adjustable feet on the cubes and fasten them to one another using the 2
supplied bolts. (see appendix 2, fig. 18)
42
I N S T A L LA T I ON M A N U A L