Husqvarna Z454X Bedienungsanweisung Seite 23

4. Connect the other end of the black cable to a
CHASSIS GROUND (D), away from the fuel tank
and the battery.
To remove the jumper cables
Note:
Remove the jumper cables in the opposite
sequence to how you connect them.
1. Remove the BLACK cable from the chassis.
2. Remove the BLACK cable from the fully charged
battery.
3. Remove the RED cable from the 2 batteries.
To remove and install the battery
1. Fold the seat forward. Refer to
page 18 .
2. Remove the bolt and the nut from the battery bracket
and remove the battery bracket from the battery.
(Fig. 51)
3. Use 2 wrenches to disconnect the black battery
cable from the negative (–) terminal on the battery.
4. Use 2 wrenches to disconnect the red battery cable
from the positive (+) terminal on the battery.
5. Carefully remove the battery from the product.
6. Install in the opposite sequence.
To adjust the tracking speed
If the product does not move straight forward, the
tracking speed must be adjusted.
WARNING:
speed in an open area without bystanders.
1. Do a check of the tire pressure. Refer to
pressure on page 23 .
2. Turn the tracking controls fully in. Refer to
overview on page 10 for the location of the tracking
controls.
3. Turn the tracking controls out 4 turns.
CAUTION:
cause damage to the product.
4. Start the product.
5. Move the control levers forward fully and operate the
product at full throttle.
6. Turn the tracking control on the right side gradually
until the product starts to move right.
7. Turn the tracking control on the left side gradually
until the product starts to move straight forward.
1741 - 002 - 22.08.2023
To fold the seat on
Always adjust the tracking
Tire
Product
More than 4 turns can
Tire pressure
Make sure to have the correct tire pressure on all 4 tires.
Technical data on page 30 .
Refer to
To remove and install the front wheels
1. Remove the nut and the bolt to remove the front
wheels from the forks. (Fig. 52)
2. Install in the opposite sequence. Torque the nut and
bolt to 50 ft-lbs / 67.8 Nm.
To adjust the anti-scalp rollers
The anti-scalp rollers keep the cutting deck in the correct
position on the ground and prevent lawn scalping in
most terrain conditions. The anti-scalp rollers can be set
in 3 positions for different lengths of grass:
• Top position: 1.5–2.5 in. / 38–64 mm grass.
• Middle position: 2.5–4 in. / 64–102 mm grass.
• Bottom position: 4–5 in. / 102–127 mm grass.
1. Park the product on level ground and stop the
engine.
2. Remove the nut, the bolt, the axle and the anti-scalp
roller. (Fig. 53)
3. Install the anti-scalp roller in one of the 3 positions.
CAUTION:
become damaged if the anti-scalp rollers
are incorrectly adjusted. The anti-scalp
rollers must be approximately 1/4 in. /
6.4 mm from the ground.
To adjust the parallelism of the cutting
deck
This procedure will set the cutting deck in a standard
position.
1. Make sure that the tire pressure is correct. Refer to
Tire pressure on page 23 .
2. Park the product on a level surface.
3. Turn the outer blade tips to align with the cutting
deck side to side. (Fig. 54)
WARNING:
cutting deck are sharp and can cause
injury. Use protective gloves.
4. Measure the distance between the ground and the
bottom of the blade tip on the discharge side of the
cutting deck. Make a note of the distance.
5. Measure the distance between the ground and the
bottom of the blade tip on the side opposite to the
discharge side. The distance must be the same as
the distance for the discharge side. If adjustment is
necessary, adjust the locknut on the top of the rear
links until the 2 side to side distances are equal. (Fig.
55)
The cutting deck can
The blades on the
23