Bosch GLL 2-10 G Professional Originalbetriebsanleitung Seite 14

A)
(19) Universal holder (BM 1)
A)
(20) Laser target plate
(21) Protective bag
A)
(22) Laser goggles
A)
(23) Tripod (BT 150)
(24) Telescopic shaft (BT 350)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Line laser
Article number
A)
Working range
B)C)
Levelling accuracy
Self-levelling range
Levelling time
Operating temperature
Storage temperature
Max. altitude
Relative air humidity max.
Pollution degree according to
IEC 61010-1
Laser class
Laser type
C
6
Divergence
Tripod mount
Batteries
Operating duration in operating mode
– Cross-line mode
– Line mode
Weight according to
EPTA-Procedure 01:2014
Dimensions (length × width ×
height)
Protection rating
A) The working range may be reduced by unfavourable environ-
mental conditions (e.g. direct sunlight).
B) At 20–25 °C
C) The values stated presuppose normal to favourable environ-
mental conditions (e.g. no vibration, no fog, no smoke, no direct
sunlight). Extreme fluctuations in temperature can cause devi-
ations in accuracy.
D) Only non-conductive deposits occur, whereby occasional tem-
porary conductivity caused by condensation is expected.
The serial number (10) on the type plate is used to clearly identify
your measuring tool.
Bosch Power Tools
Assembly
Inserting/changing the batteries
It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
To open the battery compartment cover (11), press on the
A)
locking mechanism (12) and remove the battery compart-
ment cover. Insert the batteries.
When inserting the batteries, ensure that the polarity is cor-
rect according to the illustration on the inside of the battery
compartment.
If the batteries are running low, the laser lines will gradually
GLL 2-10 G
become dimmer.
3 601 K63 P..
If the batteries are almost empty, the status indicator (8) will
flash green. The measuring tool can still be operated for ap-
10 m
proximately 1 hour after the first flash.
±0.3 mm/m
The laser lines will also flash for approximately five seconds
±4°
every ten minutes.
< 4 s
If the batteries are empty, the laser lines will flash once be-
fore the measuring tool switches off.
−10 °C to +50 °C
Always replace all the batteries at the same time. Only use
−20 °C to +70 °C
batteries from the same manufacturer and which have the
2000 m
same capacity.
90 %
u
D)
2
2
500−540 nm, < 10 mW
Working with the RM 1 rotating mount
10
(see figures A–B)
50 × 10 mrad (full angle)
You can use the rotating mount (13) to rotate the measuring
tool 360° around a central, always visible plumb point. This
1/4"; 5/8"
enables you to set up the laser lines without having to
3 × 1.5 V LR6 (AA)
change the position of the measuring tool.
B)
Place the measuring tool with the guide groove (17) on the
6 h
guide rail (14) of the rotating mount (13) and slide the
measuring tool all the way onto the platform.
12 h
To disconnect the measuring tool, pull it off the rotating
0.49 kg
mount in the opposite direction.
Rotating mount positioning options:
112 × 55 × 106 mm
– Standing on a flat surface,
– Screwed to a vertical surface,
IP 54 (dust- and splash-
– On metallic ceiling strips using the ceiling clip (18),
proof)
– On metallic surfaces using the magnets (15).
Operation
Starting Operation
u
u
Take the batteries out of the measuring tool when you
are not using it for a prolonged period of time. The bat-
teries can corrode and self-discharge during prolonged
storage in the measuring tool.
Protect the measuring tool from moisture and direct
sunlight.
Do not expose the measuring tool to any extreme tem-
peratures or fluctuations in temperature. For example,
do not leave it in a car for extended periods of time. If it
has been subjected to significant fluctuations in temper-
1 609 92A 5TD | (01.07.2020)
English | 13