Hendi 281444 Bedienungsanleitung Seite 7

Intended use
• This appliance is intended to be used for commercial appli-
cations, for example in kitchens of restaurants, canteens,
hospitals and in commercial enterprises such as bakeries,
butcheries, etc., but not for continuous mass production of
food.
• The appliance is designed only for heating and defrosting of
food products using appropriate dishes. Any other use may
lead to damage of the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Control panel
(Fig.1 on page 3)
1. Different power level and defrost
2. Time Entry
3. Double Quantity
4. Pause
5. Start
6. Number Keyboard (Button "1" is also used for program-
ming mode and multi stage cooking mode)
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
Power Up
When plug into the socket, "- - - -" will be shown on the display.
It will disappear in 1 minute of inactivity. Then, the microwave
will enter into the Idle Mode.
Idle Mode
During idle mode, the screen is blank and there will be no oven
activity. Opening and then closing the oven door will activate the
Ready Mode. The oven will enter idle mode after a minute of no
use, The time it takes to activate idle mode can be changed with
the 'user options' (Option 4, Timeout Window).
Ready Mode
Opening and closing the door while the oven is in Idle Mode will
put the oven into Ready Mode. In this mode, the oven is ready
to either begin a manual or preset cooking cycle. During Ready
Mode, 0:00 is displayed. During Ready Mode, the oven can go to
almost all of the other modes.
Door Open Mode
Door open mode is activated by opening the door. During this
mode, the screen is blank. And the fan and oven lamp work.
During operation, when the door is opened the program will be
paused, the fan keeps rotating and the light is on.
Manual Entry Mode
Make sure the microwave is under Ready Mode. Select the time
with the 'Time Entry' button, the display will show "00:00", se-
lect the requested time with the number keyboard. After that,
select the power level by pressing [0%/20%(Defrost)/50%/70%].
The display will show the selected power. If you press again the
same power level button, the power will be set back to 100%
power. Also, if no power level button is set, the power will be
default to 100% power. When everything is set, press the 'Start'
button, now the microwave will start operating. At the end of
the cycle the display will show 'End'.
Pause Mode
This mode allows users to pause the cycle to inspect or stir the
food while the microwave is operating. Open the door or press
the 'Pause' button to pause the cycle. The display will show the
remaining time. To resume the cycle, close the door and press
the 'Start' button. When nothing is done the microwave will go
into idle mode within 1 minute.
Preset program mode
This microwave comes with 10 preset programs. When the
microwave is in 'Ready Mode' press one of the number keys
and the microwave will run the program. Below you'll find the
10 preset programs. When operating the microwave shows the
remaining time in the display, when it's a multi-stage program
the total remaining time will be displayed.
Button 1
Display time 0:10
Button 6
Display time 1:30
Programming
This microwave can preset up to 100 programs. See and follow
"User options - 9 Double digit" session for setting program no.
from 10 to 100. Open the door, then press and hold number "1"
on the number keyboard for about 4 ~ 6 seconds, the buzzer will
sound and the display will show "ProG" to indicate you entered
2 3 4
0:20 0:30 0:45 1:00
7 8 9
2:00 3:00 4:00 5:00
GB
5
0
7