voestalpine bohler welding URANOS 2700 PMC Betriebsanleitung Seite 43

33 Secondary inductance (MIG Bilevel)
Allows regulation of the secondary pulsation level
inductance.
Makes it possible to obtain a quicker or slower arc to
compensate for the welder's movements and for the
natural welding instability.
Low inductance = reactive arc (more spatter).
High inductance = less reactive arc (less spatter).
Minimum -30, Maximum +30, Default syn
34 Initial increase slope
Allows to set a gradual transition between the initial
wire speed and the welding wire speed.
Parameter setting: seconds (sec.).
Minimum 0 sec., Maximum 10 sec., Default Off
35 Crater filler slope
Allows to set a gradual transition between the welding
wire speed and crater filler wire speed.
Parameter setting: seconds (sec.).
Minimum 0 sec., Maximum 10 sec., Default Off
202 Inductance
Allows electronic regulation of the series inductance of
the welding circuit.
Makes it possible to obtain a quicker or slower arc to
compensate for the welder's movements and for the
natural welding instability.
Low inductance = reactive arc (more spatter).
High inductance = less reactive arc (less spatter).
Minimum -30, Maximum +30, Default syn
331 Voltage
Lets you set welding voltage.
399 Welding speed
Lets you set welding speed.
Minimum 20cm/min, Maximum 200cm/min, Default
35cm/min (reference speed for manual welding).
Syn: allows automatic setting of the welding parameters
using the robot speed value on an analog input.
(Consult the "System configuration" section - Set up
Service).
500 Allows the selection of the required graphic interface:
XE (Easy Mode)
XA (Advanced Mode)
XP (Professional Mode)
Allows access to the higher set-up levels:
USER: user
SERV: service
vaBW: vaBW
551 Lock/unlock
Allows the locking of the panel controls and the inser-
tion of a protection code (consult the "Lock/unlock"
section).
552 Buzzer tone
Permits adjustment of the buzzer tone.
Minimum Off, Maximum 10, Default 5
601 Regulation step
Allows the regulation of a parameter with a step that can
be personalised by the operator.
Minimum 1, Maximum Imax, Default 1
602 External parameter CH1, CH2, CH3, CH4
Allows the management of external parameter 1, 2, 3,
4 (minimum value, maximum value, default value,
parameter selected).
(Consult the "External controls management" section).
606 U/D torch
Allows the management of the external parameter
(U/D).
O=off, I=current, 2=program retrieval
705 Circuit resistance calibration
Lets you calibrate the system.
Press the encoder knob to access parameter 705.
Place the tip of the wire guide in electrical contact with
the work piece.
Press and hold the torch trigger for at least 1 s.
751 Current reading
Allow the real value of the welding current to be dis-
played.
752 Voltage reading
Allows the real value of the welding voltage to be dis-
played.
757 Wire speed reading
Allow the value of the motor encoder 1 to be displayed.
760 (Motor) Current reading
Allow the real value of the (motor) current to be dis-
played.
801 Guard limits
Allows the setting of the warning limits and of the guard
limits.
Allows the accurate control of the various welding
phases (consult the "Guard limits" section).
3.7 Synergic curves screen
1 General
Allows the selection of the required welding method.
1
It allows the selection of:
Synergic welding method
Makes it possible to use a series of pre-settings
(synergic curves) available in the memory of the
system.
The changing and correction of the initial set-
tings proposed by the system is allowed.
Manual welding method
Allows the manual setting and regulation of
each individual welding parameter (MIG/
MAG).
Select however one of suggested synergies (5-6) in
order to take advantage of ignition potentiality,
closing arc features....
2/3
Lets you select:
- type of filler material
- gas type
4
Lets you select:
- wire diameter
5
- Type of filler material
- Gas type
43