Herunterladen Diese Seite drucken

Makita DF333D Betriebsanleitung Seite 12

Vorschau ausblenden Andere Handbücher für DF333D:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 70
Drilling in metal
To
prevent
the
from
slipping
when
hole, make an indentation with a center-punch and
hammer
at
the
be
drilled.
Place
of
the
drill
the
indentation and
Use
a
cutting
drilling
metals.
The
iron
and
brass
be
drilled
dry.
CAUTION:
Pressing excessively on the tool
will not speed up the drilling. In fact, this excessive
pressure
will
damage
your
decrease the
performance
the
CAUTION:
Hold the tool firmly and exert care
when the drill bit begins to break through the
workpiece. There is a tremendous force exerted on
the
tool/drill
time
through.
CAUTION:
A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it firmly.
CAUTION:
Always secure workpieces in a vise
or similar hold-down device.
CAUTION:
If the tool is operated continuously
until the battery cartridge has discharged, allow
the tool to rest for 15 minutes before proceeding
with a fresh battery.
Using the tool as a hand
screwdriver
Fig.14
Switch off the tool.
Move the reversing switch lever to the neutral position.
Turn
the
adjusting
that
the
arrow
the marking.
Turn the tool.
NOTE: This use is convenient for checking the
screwdriving.
NOTE: Do not use the tool for work requiring
excessive force,
such
tightening bolt
removing rusted
drill
bit
starting
a
point
to
the
point
bit
in
start
drilling.
lubricant
when
exceptions are
which
should
only
serve
to
the
tip
of
drill
bit,
tool
and
shorten
service life of the tool.
bit
at
the
of
hole
break
ring
so
points
to
as
or
screws.
Using holster
Optional accessory
CAUTION:
When using the holster, remove a
driver bit/drill bit from the tool.
CAUTION:
comes to a complete stop before placing it in the
holster. Be sure to close the holster securely with
the holster button so that it holds the tool firmly.
1.
Thread
or
holder. ► Fig.15:
Waist
2.
Put
the
it
button.
Fig.16
Fig.17
You
can
bits
at
the
holster.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To
maintain
RELIABILITY,
maintenance
be
performed by
Authorized or
Centers,
always
replacement
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual.
of
accessories or attachments might present
a risk of injury
use
attachment for its stated purpose.
12 ENGLISH
Turn off the tool and wait until it
a
waist
similar
through
1. Holster holder 2.
belt
the
tool
holster
and
with
the
keep
two
the
front
product
SAFETY
repairs,
any
or
adjustment should
Makita
Factory
Service
using
Makita
parts.
The
any
other
to
persons.
accessory or
belt
holster
in
lock
holster
driver
of
and
other
use
Only

Werbung

loading

Diese Anleitung auch für:

Df033d