Gardena PowerMax Li-40/32 Betriebsanleitung Seite 12

Our products are double insulated to EN 60335. Do not connect an earth to any
part of the product.
Check the working area for hidden cables.
Do not use for pond care or close to water.
Personal safety
DANGER! Risk of suffocation!
Small parts can be easily swallowed. There is also a risk that the polybag can
suffocate toddlers. Keep toddlers away when you assemble the product.
Do not use in explosive atmosphere.
Never operate the product when you are tired, ill or under the influence of alcohol,
drugs or medicine.
Do not overload the mower.
Use gloves, wear slip resistant shoes and wear eye protection.
Do not use under wet conditions.
Do not disassemble the product further than the delivery status.
Only start the mower with an upright standed handle.
Do not use the start levers alternately.
Use the handles carefully.
Safety Cut-Out
The engine is protected by a Safety Cut-Out which is activated when the blade
becomes jammed or if the engine is overloaded. When this occurs, stop and
disconnect the product from the mains. The Safety Cut-Out will only reset when
you release the start / stop lever. Clear any obstruction and wait for a few minutes
for the Safety Cut-Out to reset before you continue to use the product.
2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the blade turns or the product starts
accidentally.
v Wait for the blade to stop, remove the safety key and use
gloves before you do assembly.
To connect the lower handle [ Fig. A1 ]:
1. Put the lower handle (1) in the product.
Make sure that the handles are fully in place and the handle hole
is inline with the threaded hole.
(2)
2. Put the washer on the wing screw
3. Put the wing screw (3) in the threaded hole in the product.
(3)
4. Tighten the wing screw
To connect the upper handle [ Fig. A2 ]:
1. Put the upper handle (4) on the lower handle
Make sure that the handles are fully in place and the handle holes
are inline.
(5)
2. Push the screw through the hole.
3. Put the washer (2) and the wing nut
(6)
4. Tighten the wing nut .
To fix the cable to the handle [ Fig. A3 ]:
(7)
1. Fix the cable to the handle with the clip
2. Check that the cable (7) is not trapped between the lower and
the upper handle.
To assemble the grass box [ Fig. A4 / A5 ]:
1. Turn the cover (10) on the grass box.
Make sure that the cover
2. Push the cover (10) on the grass box until the connections click.
Make sure that all connections are connected.
3. Push the handle (11) into the cover
(9)
4. Push the chute into the grass box and pull the chute
until it audibly engages.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the blade turns or the product starts
accidentally.
v Wait for the blade to stop, remove the safety key and use
gloves before you attach the battery or transport the product.
12
5033-20.960.04.indd 12 5033-20.960.04.indd 12
(3)
.
.
(1) .
(6) on the screw (5) .
(8)
.
(10) aligns to the grass box.
(10) until it clicks.
(9)
forward
To charge the battery [ Fig. O1 ]:
DANGER! Risk of injury!
Damage to the battery or the battery charger!
Overvoltage damages the battery and the battery charger.
v Make sure that you use the correct mains voltage.
Before you use the battery the first time, the battery must be fully
charged.
The lithium-ion battery can be charged in any state of charge and the
charging process can be disconnected at any time without to damage
the battery (no memory effect).
For GARDENA Electric Lawnmower Art. 5033-20:
The GARDENA Battery BLi-40/100 Art. 9842 is in the scope
of delivery.
(14)
1. Connect the mains cable to the battery charger
2. Connect the mains cable (14) to a 230 V mainssocket.
(12)
3. Connect the charger cable to the battery
When the charging control lamp
once per second the battery is being charged.
When the charging control lamp
green the battery is fully charged. For charging time,
see 7. TECHNICAL DATA.
4. Check the charge status regularly while you charge.
5. When the battery is fully charged, disconnect the battery
X
battery charger .
6. Disconnect the mains cable (14) from the mains.
Battery charging indicator [ Fig. O2 ]:
Battery charging indicator during charging:
« ∑
100 % charged , and
67 – 100 % charged « and ∑
« ∑
34 – 66 % charged lit, flashing
0 – 33 % charged « flashing
Battery charging indicator during operation:
Push the button Y on the battery.
67 – 100 % charged « , ∑ and
« ∑
34 – 66 % charged and
11 – 33 % charged « lit
«
0 – 10 % charged flashing
To start the mower [ Fig. O3 / O4 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example do
not attach the start lever (17) to the handle.
To start:
The product is fitted with a two-handed safety device (start lever
with safety interlock (16) ) to prevent the product from being turned
on by accident.
(17)
There are two start levers fitted. Either one have to be used to start.
1. Open the lid (18) .
(13)
2. Put the battery into the product.
3. Put the safety key (19) into the product and turn to position 1.
(16)
4. Push the safety interlock with one hand and pull the start lever
with the other hand.
(16)
5. Release the safety interlock .
The product will start.
To stop:
1. Release the start lever (17) .
(19) to positon 0 and remove it.
2. Turn the safety key
To adjust the cutting height [ Fig. O5 ]:
The cutting height can be adjusted from 2 to 6 cm in 12 positions.
1. Push and turn the adjust wheel (20)
(20)
2. Push and turn the adjust wheel
cutting height.
X
.
(13)
.
(15) at the charger flashes green
(15) at the charger is lit
(13) from the
€
lit
lit, € flashing
€ lit
lit
(17)
clockwise to lower the cutting height.
counterclockwise to increase the
08.04.22 14:02 08.04.22 14:02
(17)