Inhaltsverzeichnis; Introduction; Kit Contents - FMS J-11 Bedienungsanleitung

Introduction

The J-11 fighter is a domestic version of the Su-27 that the
People's Republic of China authorized from Russia. It is a
third-generation fighter. The Shenyang Aircraft Company
established a production line, and Russia supplied the main
parts and systems to form production and assembly capabilities.
Later, China carried out independent research and development
on its basis, and derived newer models such as J-11B and
J-11BS.
Superlative dark gray paint, smooth aerodynamic contour,
outlines a unique sense of modern technology- FMS dual 70mm
EDF J-11.
In terms of performance, Dual 70mm inrunner 12 bladed EDFs
and high-quality 80A ESCs provide ample thrust for high speed,
excellent vertical performance and resonating turbine engine
sound. In addition, the pre-installed metal gear servos and ball
link style control horns make for more responsive and precise
operation.
In terms of appearance, FMS captures the essence of this
fighter. Functional restoration, such as large size airbrake, LED
navigation lights & landing lights, full-motion tail, landing gear
door with sequencing effect, retractable landing gear system
that can resist hard landings, static restoration such as cockpit
details, panel lines, detachable ordnance, pilot, and highly
recognizable trim scheme, all these details combine to make the
FMS J-11 stand out on the tarmac and in flight.
Get yourself a J-11 and bring new excitement to the flying field!

Kit contents

Before assembly, please inspect the contents of the kit. The
photo below details the contents of the kit with labels. If any
parts are missing or defective, please identify the name or
part number (refer to the spare parts list near the end of the
manual) then contact your local shop or email us: support
@fmsmodel.com.
Specifications
Wing span:1110mm /43.7in
Overall length: 1640mm /64.5in
Flying weight: ~ 4380g
Motor size: 3060-KV1900
Wing load:134.8 g/dm²
Wing area: 32.5 dm²
ESC: 80A*2
Servo: 13gX2，9gX8
Recommended battery: 22.2V 5000mAh-6000mAh 50C
Key Features
1.Dual 70mm inrunner 12 bladed EDFs and high-quality 80A
ESCs provide ample thrust.
2.High degree of reduction of dynamic and static details.
3.High-quality wear-resistant rubber tires.
4.Electronic retracts with locked-rotor mode and over current
protection.
5.Large-size bearings are used in the wheel hub for take-offs
and landings on rough roads.
6.Pre-installed, newly designed ball link style control horns for
more throw.
Table of contents
Introduction ·····························································
Kit contents ····· ·························································3
Model assembly ·······················································4
Battery installation ·············································
Receiver diagram
·····
Get your model ready to fly
Control horn and servo arm settings
Center of gravity(CG)
Before flying the model
Flying course ·························································12
Troubleshooting
······················································13
Spare parts list content
User Manual of Brushless Speed Controller
A.
C.
G.
F.
I.
A:Fuselage
B:Horizontal stabilizer
C:Main wing
D:Vertical stabilizer
E:Ventral fins
3
·········································
································
·····························
···············································11
············································
············································
················
B.
D.
E.
H.
J.
F:Armaments
G:Tailcone
H:Cowl
I :Spars
J:Linkage rods and screw set
(HKM3.0X16*8，HKM3.0X10*2
3X4*2 )
E
N
3
····· ······ 9 ··
······ 9 ··
·· ····· ·· 9
11
12
13
14