Mounting And Operation - Bosch UniversalGrassCut 18V-26 Originalbetriebsanleitung

– Vibration emission value a
h
– Uncertainty K
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.

Mounting and Operation

Action
Product Features
Delivery scope
Mounting the protection guard
Adjusting the working height
Folding out the handle
Mounting the wheel
Battery charging and inserting
Switching On and Off
Recommended position for grass
cutting
Recommended position for edge
trimming
Recommended position for cutting
under bushes
Removing the line spool
Winding line on spool
Mounting the line spool
Maintenance, Cleaning and Stor-
age
Accessories
Bosch Power Tools
2
m/s
2
m/s
Assembly
Caution: Switch the garden tool off and remove the
u
battery before performing any maintenance.
Mounting the protection guard (see figure C)
Slide the protection guard (5) onto the trimmer head until a
click can be heard. Affix the protection guard (5) to the trim-
mer with the screw. The screw is already fitted to the bottom
housing upon delivery.
Never use the trimmer without the protection guard (5)
mounted. After mounting, the protection guard (5) may not
be removed from the trimmer.
Adjusting the working height (see figure D)
Press button (10) and adjust the trimmer to the desired
height. Release button (10).
Always use the trimmer in a working position, never in the
storage position. The storage position is when the trimmer is
fully retracted. When adjusting the working position, make
sure that the mechanism for height adjustment is properly
locked. A click can be heard when the mechanism engages.
Folding out the handle (see figure E)
Figure Page
A 329 Press and hold button (7), fold out the handle (3) to the stop
and then release button (7). Make sure that the handle (3) is
B 330
properly locked. Do not put the pressure on the handle (3)
C 330
while adjusting it.
D 331
Mounting the wheel (see figure F)
E 332
Mount wheel (6) to the trimmer head. Observe correct posi-
F 332
tion of the arrows on the trimmer head. Ensure that the hook
G 333
engages properly in the tab. Turn the wheel (6) against the
H 333
trimmer head until the lever (11) can be heard to engage
with a click.
I 334
To remove, pull lever (11) until it disengages and remove the
wheel (6) in opposite direction.
J 335
Switching on
K 336
Caution: Switch garden tool off and remove battery
u
L 337
from machine before adjusting or cleaning.
M 338
Charging the Battery
N 339
Pay attention to the mains voltage. The voltage of the
u
O 339
power source must match the voltage specified on the
rating plate of the charger.
P 340
The battery is equipped with temperature monitoring that al-
lows charging only in the temperature range between 0 °C
and 35 °C. In this manner, a high battery service life is
achieved.
English | 19
Lawn trimming Edge cutting
7
= 1.5
F 016 L94 460 | (21.07.2022)
7
= 1.5