Handle Adjustment - Kinderkraft NEWLY Bedienungsanleitung

III. STROLLER FRAME ASSEMBLY
Release the locking element (FIG.A) While holding the frame, lift the handle until you hear the characteristic locking sound
(FIG.B)
IV. ASSEMBLY AND DISASSEMBLY OF THE FRONT WHEELS
Slide the front wheels (7) into their designated holes until you hear a locking sound (FIG.C). To release the wheel press the
button and pull out the wheel ( Fig.D).
V. ASSEMBLY AND DISASSEMBLY OF THE REAR WHEELS
Slide the axles of the rear wheels (11) into the designated holes until you hear a locking sound (FIG.E). To release the wheel
press the button and pull out the wheel ( Fig.F ).
WARNING! Make sure all wheels are properly installed before using the
stroller.
VI. BRAKE
Activate the brake (FIG.G). Lift the brake to disengage the lock (FIG.H).
VII. ASSEMBLY AND DISASSEMBLY OF THE SEATS
Push the seat connector (17) into the frame socket (4) until you hear a distinctive click( Fig.I) and fasten the straps under
the seat (FIG.J.I). Adjust the buckle behind the backrest as much as possible towards the backrest by pressing the buckle
towards the seat (FIG. J.II). The seat can be mounted forward or rearward facing ( Fig.K). Press the seat release lever(16)
from the frame(4) on both sides and pull upward (Fig.L) to remove the seat.
VIII. ASSEMBLY AND DISASSEMBLY OF THE HOOD
Insert the hood into the click-fits. Secure with hook-and-loop fasteners and tighten all the way around (Fig. M). To
disassemble, perform operations in reverse order. (Fig. N)
ATTENTION: ASSEMBLE THE HOOD BEFORE USING THE STROLLER."
IX. ASSEMBLY AND DISASSEMBLY OF THE BUMBER BAR
Slide the bumber bar into the appropriate places on the frame( Fig.O). Remove the bumber bar by pressing the buttons on
both sides of the frame and pulling it out( Fig.P).
X. SAFETY HARNESS
Clip the harness into the buckle (FIG.Q.I). Adjust the harness each time ( FIG.Q.II). There are three possible heights for
mounting the shoulder harness. Press the button to unbuckle the harness (FIG.R). For assembly/disassembly, the shoulder
straps, hip belts and crotch belt should be moved through the holes in the seat.
XI. SEAT ADJUSTMENT
The seat has reclining and sitting positions the seat angle can be adjusted with a lever (18) ( FIG. S.). The option to adjus t
the seat to the lowest possible position is only used to turn the seat into a carry cot.
XII. HANDLE ADJUSTMENT
Press the handle adjustment button ( 1) and adjust to one of three positions. (FIG.T)
XIII. ASSEMBLING THE LEG WARMER AND RAINCOVER.
Secure the leg warmer with naps on both sides (Fig.U).
Put the raincover on the seat or carrycot (Fig.V).
XIV. DISASSEMBLY OF THE STROLLER
Position the seat forward/rearward facing ( Fig.W).Using the lever, fold the seat (FIG.X), pull both folding levers(13) towards
each other to fold the stroller( Fig.Y). When the stroller is fully folded, the Frame should be secured with a lock on the side
(FIG.Z).
XV. STROLLER CARRYCOT
To convert the stroller seat into a carrycot, use the folding lever to lower the seat down as far as possible (FIG.AA) and
unbuckle the strap located under the seat (FIG.AB.I) and lower the backrest as far as possible with the buckle (FIG.AB.II).
The correctly assembled carrycot is shown in (FIG. AC). NOTE: Belts in the carrycot version should be demoted. Removal of
the straps is described in Chapter X.
WARNING! The carrycot may only be mounted rearward facing (child facing
the person operating the stroller).
XVI. CAR SEAT ASSEMBLY/DISASSEMBLY
The included adapters are compatible with the following car seats: Kinderkraft Mink, Kiddy Evoluna i-Size 2, Kiddy Evolution
Pro 2, Cybex Aton 5, Cybex Aton M, Cybex Aton M i-Size, Cybex Aton B2, Cybex Aton S2 i-Size, Cybex Cloud Z i-Size, Maxi
Cosi Cabriofix i-Size, Maxi Cosi Pebble Pro, Maxi Cosi 360, Maxi Cosi Rock, Maxi Cosi Tinca, Maxi Cosi Citi, BeSafe izi Go
26