Technical Data - EINHELL TE-MS 254 T Originalbetriebsanleitung

tion regulations in force in your area. The same
applies for the general rules of health and safety
at work.
The manufacturer will not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes. Even when the ma-
chine is used as prescribed it is still impossible to
eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the blade in the uncovered saw
zone.
•
Reaching into the running blade (cut injuries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Blade fracturing.
•
Catapulting of faulty carbide tips from the bla-
de.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.

4. Technical data

AC motor: ............................... 220-240 V ~ 50 Hz
Power: .................................................... 2000 W
Operating mode: ............................................. S1
Idle speed n : .....................................5,000 min
0
Carbide blade: .................. ø 254 x ø 30 x 2.8 mm
Number of teeth: ............................................ 36
Dust extraction connector: .....................ø 36 mm
Weight: .....................................................17.3 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: .......................................... ≤ 1 mW
Protection class: ........................................... II/
For use as a bench-type saw:
Table ............................................. 481 x 289 mm
Cutting depth ................................... max. 50 mm
Maximum cross-section of the workpiece
........................................................ 170 x 50 mm
Minimum size of the workpiece 30 x 10 x 100 mm
Thickness of the splitter .......................... 2.3 mm
For use as a crosscut saw:
Pivoting range ............................. -45° / 0° / +45°
Miter cut ................................. 0° to 45° to the left
Sawing width at 90° ........................ 130 x 74 mm
Anl_TE-MS_254_T_SPK13.indb 29
GB
Sawing width at 45° .......................... 65 x 74 mm
Sawing width at 2 x 45° to the left
(double miter cut) ............................. 35 x 50 mm
Sawing width at 2 x 45° to the right
(double miter cut) ............................. 85 x 50 mm
Minimum size of the workpiece 50 x 10 x 180 mm
Danger!
Noise
The noise emission values were measured in ac-
cordance with EN 61029.
L sound pressure level ...................... 103 dB(A)
pA
K uncertainty ........................................ 3 dB(A)
pA
L sound power level ......................... 116 dB(A)
WA
K uncertainty ........................................ 3 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
-1
Warning:
The noise emission levels may vary from the level
specified during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
- 29 -
10.05.2023 15:03:52