EINHELL TE-MS 254 T Originalbetriebsanleitung Seite 34

7.2 Use as a crosscut saw and as a miter saw
(Fig. 1)
Set the saw to crosscut mode (see 5.2).
7.2. 1 Crosscut 90° and turntable 0°
(Fig. 1-3, 32)
•
Place the piece of wood to be cut against the
stop rail (10) and on the turntable (12).
•
Use the clamping device (21) to secure the
workpiece on the fixed saw table (18) so that
it will not move during the cutting operation.
•
Press and hold the On/Off / switch (4) to
switch on the saw.
•
When you have switched on the saw, wait for
the blade (6) to reach its maximum speed.
•
Press the release button (2) and, using the
handle (3), apply uniform and light pressure
to move the machine head (1) down through
the workpiece.
•
When the cutting operation is completed,
move the machine head (1) back to its up-
per (home) position and let go of the On/Off
switch (4).
•
Warning! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (3) after cutting,
but allow the machine head (1) to rise slowly,
applying slight counterpressure as it does so.
7.2.2 Crosscut 90° and turntable 0°- 45°
(Fig. 1-3, 33)
You can use the saw to make angular cuts of 0°-
45° to the left and right in relation to the stop rail.
•
Move the machine head (1) to its upper posi-
tion.
•
Release the turntable (12) by slackening the
locking screw (15).
•
While holding down the release button (14),
turn the turntable (12) and the pointer (17) to
the desired angle on the scale (16).
•
Retighten the locking screw (15) to secure the
turntable (12) in place.
•
Make the cut as described in section 7.2.1.
7.2.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1- 3, 34)
The saw can be used to make miter cuts of 0° -
45° in relation to the work face.
•
Move the machine head (1) to its upper posi-
tion.
•
Fasten the turntable (12) in 0° position.
•
Release the locking grip (22) and use the
handle (3) to tilt the machine head (1) to the
left until the pointer (24) coincides with the
required angle on the scale (23).
Anl_TE-MS_254_T_SPK13.indb 34
GB
•
Retighten the locking grip (22) and make the
cut as described in section 7.2.1.
7.2.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 35)
The saw can be used to make miter cuts to the
left of 0°- 45° in relation to the work face and, at
the same time, bevel cuts of 0°- 45° in relation to
the stop rail (double miter cut).
•
Move the machine head (1) to its upper posi-
tion.
•
Release the turntable (12) by slackening the
locking screw (15).
•
While you are holding down the release but-
ton (14), turn the turntable (12) to the desired
angle.
•
Retighten the locking screw (15) to secure the
turntable (12) in place.
•
Release the locking grip (22) and use the
handle (3) to tilt the machine head (1) to the
left to the desired angle.
•
Retighten the locking grip (22) and make the
cut as described in section 7.2.1.
7.3 Use as a bench-type circular saw (Fig. 4)
Set the saw to table mode (see 5.3).
Warning! For table mode the machine head (1)
is not allowed to be tilted to the left, i.e. the miter
angle on the scale (23) must equal 0°.
7.3.1 Making longitudinal cuts (Fig. 4, 36)
This entails cutting through the workpiece in its
longitudinal direction.
Press one edge of the workpiece against the pa-
rallel stop (43) while the fl at side lies on the saw
table (37).
The blade guard (39) must always be lowered
over the workpiece.
When you make a longitudinal cut, never adopt
a working position that is in line with the cutting
direction.
•
Adjust the parallel stop (43) in accordance
with the required width and clamp securely.
(See 6.7.)
•
Press the green button „I" of the On/Off switch
(38) to switch on the saw.
•
With your fingers closed, place your hands
flat on the workpiece and push the workpiece
along the parallel stop (43) and into the blade
(6).
•
Guide at the side with your left or right hand
(depending on the position of the parallel
stop) only as far as the front edge of the gu-
- 34 -
10.05.2023 15:03:55