EINHELL TE-MS 254 T Originalbetriebsanleitung Seite 33

screwdriver supplied with this product.
6.4 Precision adjustment of the angle stop
for 45° miter cuts (Fig. 24/26)
•
Lower the machine head (1) and fasten in
place with the retaining pin (33).
•
Fasten the turntable (12) in 0° position.
•
Undo the locking grip (22) and tilt the machi-
ne head (1) all the way to the left to 45° using
the handle (3).
•
Place the 45° stop angle (b) between the bla-
de (6) and the turntable (12).
•
Slacken the lock nut (27) and adjust the ad-
justment screw (26) until the angle between
the blade (6) and the turntable (12) equals
exactly 45°.
•
Retighten the lock nut (27) to secure this set-
ting.
•
There is no angle stop (b) supplied with this
product.
6.5 Laser for crosscut mode (Fig. 27)
Switching on: Move the laser On/Off switch (31)
to the " " position to switch on the laser (30). A
laser line will be projected onto the workpiece you
want to process, providing an exact guide for the
cut.
Switching off : Move the On/Off laser switch (31)
to the "OFF" position.
Important! The laser function is designed only
for crosscut mode. Switch off the laser (30) before
you convert the saw for table mode.
Set the saw to table mode (see 5.3).
6.6 Precision adjustment of the saw table
lock (Fig. 28/29)
During table mode the saw table (37) must be fas-
tened as securely as possible in order to ensure
safe operation. If necessary you can use the two
depth stops to readjust the play for the saw table
(37):
•
Use the stop screw (34) to limit the play
caused by the retaining pin (33).
•
Use the stop screw (36) to limit the play
caused by the latching pin (35).
•
Caution! Adjust the stop screws (34, 36) only
to the point where you can still engage the re-
taining pin (33) or the latching pin (35) without
any additional force.
•
The lock of the saw table (37) must be che-
cked regularly.
Anl_TE-MS_254_T_SPK13.indb 33
GB
6.7 Parallel stop (Fig. 30)
The parallel stop (43) must be used when making
longitudinal cuts in wooden workpieces. War-
ning! When you mount or adjust the parallel stop
(43) you must always make sure that it is aligned
parallel to the blade (6).
•
The parallel stop (43) can be mounted on eit-
her side of the saw table (37).
•
Fit the parallel stop (43) on the saw table (37)
from the side.
•
Use the two scales (45) on the saw table (37)
to adjust the parallel stop (43) to the required
dimension.
•
You can clamp the parallel stop (43) in the re-
quired position by pressing the clamping lever
(44).
7. Operation
Warning!
•
After every new adjustment we recommend
you to make a trial cut in order to check the
new settings.
•
After switching on the saw, wait for the blade
to reach its maximum speed of rotation before
commencing with the cut.
•
Take extra care when starting the cut!
•
Never use the machine without the suction
function.
•
Check and clean the suction channels regu-
larly.
•
Never try to combine crosscut mode and tab-
le mode.
7.1 On/Off switch (Fig. 31)
For crosscut mode:
•
Press the On/Off switch (4) to start up the
saw.
•
The On/Off switch (4) must be held during
crosscut mode.
•
Let go of the On/Off switch (4) to switch off
the saw.
For table mode:
•
Press the green button „I" of the On/Off switch
(38) to switch on the saw.
•
To switch off the saw again, press the red "O"
button.
- 33 -
10.05.2023 15:03:54