Product Lifetime; Cleaning And Maintenance - 3M PELTOR WS ALERT X Bedienungsanleitung

SMART TIP: If the headset has been reset to factory default,
it automatically enters pairing mode the first time the headset
is powered on again.
10. TROUBLESHOOTING
Problem Possible Issue/Solution
The Make sure the battery in the headset is fully
headset charged.
will not
Poor battery. Replace the battery.
power on.
Make sure the Bluetooth device to pair is set
to pairing mode and ready for pairing.
The Bluetooth device to pair is out of range.
1. Remove all Bluetooth devices that are
synchronized to your phone.
Pairing
2. Restart the phone (power on/off your
failed.
phone).
3. Do a factory reset on the headset.
4. Pair your headset to your phone.
5. If the problem remains, try to pair another
phone to see if it helps.
Bluetooth is a radio technology which means
I hear
it is sensitive to objects between the headset
crackling
and the device it is connected to. You should
noises
be able to have up to 10 meters of distance
during
between the headset and the connected
streaming/
device if within line of sight (i.e. no walls etc).
phone
Even the location of the phone on the body
calls.
may be of significance.
Make sure the battery in the headset is fully
charged.
I have a
problem
Poor battery. Replace the battery.
with the
FM radio
Radio reception depends on topography and
reception.
the environment you are in. If the reception
is poor, try to change area.

11. PRODUCT LIFETIME

It is recommended that you replace your product within
5 years from date of manufacture. The lifetime of the product
will be highly dependent on the environment in which the
product is stored, used, serviced, and maintained. The user
must regularly inspect the product to determine when it has
reached its end of life. Examples that the product may have
reached its end of life are:
• Visible defects such as cracks, deformations, loose or
missing parts.
• Experience of a deterioration in the hearing protector's
attenuation performance, strange noise or abnormal high
sound volumes from the product's electronic sound
reproduction.
NOTE: Product lifetime does not include batteries.

12. CLEANING AND MAINTENANCE

Carry out a visual battery condition check. Replace if battery
leakage or defects are detected.
Use a cloth wetted with soap and warm water to clean the
outer shells, headband and ear cushions.
NOTE: Do NOT immerse the hearing protector in water.
If the hearing protector gets wet from rain or sweat, turn the
earmuffs outwards, remove the ear cushions and foam liners,
and allow to dry before reassembly. The ear cushions and
foam liners may deteriorate with use and should be examined
at regular intervals for cracking or other damage. When used
regularly, 3M recommends replacing the foam liners and ear
cushions at least twice a year to maintain consistent
attenuation, hygiene, and comfort.
In hot and humid environments more frequent changes may
be required to maintain acceptable
is damaged, it should be replaced. See Spare Parts Section
below.
12.1. REMOVING AND REPLACING THE EAR
CUSHIONS
(Figure H:11 - H:13)
H:11 To remove the ear cushion, slide your fingers under the
inside edge of the ear cushion and firmly pull straight
out.
H:12 Remove existing liner(s) and insert new foam liner(s).
H:13 Fit one side of the ear cushion into the groove of the
earcup and then press on the opposite side until ear
cushion snaps in place.
12.2. REMOVING AND REPLACING OUTER
SHELLS
(Figure 1)
To remove the outer shells:
Insert your fingers or a tool under the edge of the outer shell
clamp and pull out and down to unlock the outer shell.
Remove the shell by lifting from the bottom edge.
To attach the outer shells:
Press down on the clamp of the outer shell to ensure it is in
the unlock position. Position the tab on top edge of outer shell
into the slot on the top edge of the earcup.
When the outer shell is pressed fully into place, push the
clamp upwards to lock the outer shell to the earcup.
EN
hygiene. If an ear cushion
7