Maintenance; Optional Accessories - Makita DJS130 Betriebsanleitung

Adjusting shear blade (Fig. 12)
Adjust the side blade L so that the curl of waste material
does not contact the cutting head or the workpiece. Use
the hex wrench to loosen the three screws which hold the
cutting head. Move the side blade L back and forth to
adjust it. Then tighten the three screws with the hex
wrench.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Lubrication (Fig. 13)
Before operation, lubricate the contact point of the center
blade and the side blades R/L. And, also lubricate the
point of the center blade near the cutting head. To keep
good cutting performance, use lubricant from time to time
during operation.
Replacing carbon brushes
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes. (Fig. 14)
First remove the holder by unscrewing the hex socket
head bolt. (Fig. 15)
Then loosen the hex socket head bolt that fastens the
barrel and turn the barrel counterclockwise. (Fig. 16)
Use a screwdriver to remove two screws then remove the
front cover. (Fig. 17)
Raise the arm part of the spring and then place it in the
recessed part of the housing with a slotted bit screw-
driver of slender shaft or the like. (Fig. 18)
Use pliers to remove the carbon brush caps of the car-
bon brushes. Take out the worn carbon brushes, insert
the new ones and replace the carbon brush caps in
reverse. (Fig. 19)
Make sure that the carbon brush caps have fit into the
holes in brush holders securely. (Fig. 20)
Reinstall the front cover and tighten two screws securely.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by Mak-
ita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Center blade
• Side blade R
• Side blade L
• Hex wrench
• Various type of Makita genuine batteries and chargers
• Shear head 16 set
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: cutting sheet metal
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufac-
turer declare that the following Makita machine(s):
Designation of Machine:
Cordless Metal Shear
Model No./ Type: DJS130
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorized
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
30.1.2009
Tomoyasu Kato
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
): 79 dB (A)
pA
2
): 5.5 m/s
h, CM
2
Director
ENG905-1
ENG900-1
ENG901-1
ENH101-15
7