Operation; Maintenance - Makita DJS130 Bedienungsanleitung

Indicator lamps
Lighted Off
015658
NOTE:
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Switch action (Fig. 4)
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
• When not operating the tool, depress the trigger-lock
button from B side to lock the switch trigger in the
"OFF" position.
To prevent the switch trigger from accidentally pulled, the
trigger-lock button is provided.
To start the tool, depress the trigger-lock button from A
side and pull the switch trigger.
Release the switch trigger to stop. After use, always
press in the trigger-lock button from B side.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before adjusting or checking
function on the tool.
Replacement of blades
CAUTION:
• Never remove the blades with bare hands. Wear
gloves. Otherwise it can cause injury.
Removing cutting head (Fig. 5)
Use the hex wrench to loosen the three screws which
secure the cutting head. Pull the cutting head straight out
to remove it with turning it left and right alternately.
6
Remaining
Capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery may
have
malfunctioned.
Removing shear blades (Fig. 6)
Remove the three screws which hold the cutting head.
When removing the second screw, be careful not to fall
the sleeve. Then the blades can be removed easily.
When removing the blades, hold the blades and the
sleeve so that they do not fall from the cutting head.
Installing shear blades (Fig. 7)
Install the sleeve and tighten the three screws after
inserting the center blade, side blade L & R into the cut-
ting head. In this process, the screw heads should be
protruding 2 – 3 mm from the cutting head surface.
If you will tighten the screws excessively, the cutting
head cannot be installed to the tool.
Installing cutting head (Fig. 8)
CAUTION:
• Secure the cutting head firmly. Otherwise it can rotate
during operation and can cause serious injury.
Insert the cutting head into the tool with turning it left and
right alternately. Then tighten the three screws with the
hex wrench.
Hex wrench storage (Fig. 9)
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
Carry hook (Fig. 10)
The carry hook is convenient for temporarily hooking the
tool. It can be installed on either side of the tool.
When removing the carry hook, widen it by pressing its
right ends ON BOTH SIDES in the directions of arrow (1)
and raise it in the direction of the arrow (2).

OPERATION

CAUTION:
• Edges and chips of the workpiece are sharp. Wear
gloves. Otherwise it can cause injury.
Secure the workpiece firmly. Move the tool forward keep-
ing the side blades flush with the workpiece surface.
(Fig. 11 & 12)
Adjusting shear blade (Fig. 13)
Adjust the side blade L so that the curl of waste material
does not contact the cutting head or the workpiece. Use
the hex wrench to loosen the three screws which hold the
cutting head. Move the side blade L back and forth to
adjust it. Then tighten the three screws with the hex
wrench.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.