Maintenance - Makita LS1016 Bedienungsanleitung

Position in
Miter angle
Fig. A
(1) Right 45°
For inside
corner
(2)
Left 45°
(3)
For outside
corner
(4) Right 45°
006365
7. Cutting aluminum extrusion
Fig.50
When securing aluminum extrusions, use spacer
blocks or pieces of scrap as shown in the figure to
prevent deformation of the aluminum. Use a
cutting lubricant when cutting the aluminum
extrusion to prevent build-up of the aluminum
material on the blade.
WARNING:
Never attempt to cut thick or round aluminum
•
extrusions. Thick or round aluminum extrusions
can be difficult to secure and may work loose
during the cutting operation which may result in
loss of control and serious personal injury.
8. Groove cutting
Fig.51
A dado type cut can be made by proceeding as
follows:
Adjust the lower limit position of the blade using
the adjusting screw and the stopper arm to limit the
cutting depth of the blade. Refer to "Stopper arm"
section described previously.
After adjusting the lower limit position of the blade,
cut parallel grooves across the width of the
workpiece using a slide (push) cut as shown in the
figure. Then remove the workpiece material
between the grooves with a chisel.
WARNING:
Do not attempt to perform this type of cut by
•
using a wider type blade or dado blade.
Attempting to make a groove cut with a wider blade
or dado blade could lead to unexpected cutting
results and kickback which may result in serious
personal injury
Be sure to return the stopper arm to the
•
original position when performing other than
groove cutting. Attempting to make cuts with the
stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which
may result in serious personal injury.
Carrying tool
Fig.52
Make sure that the tool is unplugged. Secure the blade
at 0° bevel angle and the turn base at the full right miter
angle position. Secure the slide poles so that the lower
Table (C)
Finished piece
Save the right side of blade
Save the left side of blade
Save the right side of blade
Save the left side of blade
slide pole is locked in the position of the carriage fully
pulled to operator and the upper poles are locked in the
position of the carriage fully pushed forward to the guide
fence (refer to the section titled "Slide lock adjustment ".)
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin.
Carry the tool by holding both sides of the tool base as
shown in the figure. If you remove the holders, dust bag,
etc., you can carry the tool more easily.
Fig.53
WARNING:
Stopper pin is only for carrying and storage
•
purposes and should never be used for any
cutting operations. The use of the stopper pin for
cutting operations
movement of the saw blade resulting in kickback
and serious personal injury.
CAUTION:
Always secure all moving portions before carrying
•
the tool. If portions of the tool move or slide while
being carried loss of control or balance may occur
resulting in personal injury.

MAINTENANCE

WARNING:
Always be sure that the tool is switched off and
•
unplugged
inspection or maintenance. Failure to unplug and
switch off the tool may result in accidental start up
of the tool which may result in serious personal
injury.
Always be sure that the blade is sharp and
•
clean for the best and safest performance.
Attempting a cut with a dull and /or dirty blade may
cause kickback and result in a serious personal
injury.
NOTICE:
Never use gasoline, benzine, thinner, alcohol or
•
the like. Discoloration, deformation or cracks may
result.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1. Miter angle
Push the carriage toward the guide fence and
tighten the locking screw clockwise and pull the
lock lever towards the front of the saw to secure
the carriage.
Turn the grip counterclockwise which secures the
turn base. Turn the turn base so that the pointer
points to 0° on the miter scale. Then turn the turn
base slightly clockwise and counterclockwise to
seat the turn base in the 0° miter notch. (Leave as
it is if the pointer does not point to 0°.) Loosen the
20
may cause
before attempting
unexpected
to perform