Hendi 273869 Benutzerhandbuch Seite 9

Intended use
• This appliance is designed for warming, and not for illumi-
nate. Any other use may lead to damage of the appliance or
personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Internal wires of power cord: Connection with the electrical
wires from the power system
2. Hooking hole: Hanging the lamp to the ceiling
3. Rotating knob: Adjusting the power cord length
4. Cap cover: Fix the length of the power cord after setting
5. ON (I) / OFF (0) switch: Switch ON / OFF the lamp
6. Lamp shade: Control the direction of the light
Preparation before use
• Remove all protective packaging and wrapping.
• Check to make sure the appliance is undamaged and with
all accessories. In case of incomplete delivery and damages.
Please contact supplier immediately. Do not use the appli-
ance.
• Clean the appliance before use (See == > Cleaning & Main-
tenance).
• Make sure the appliance is completely dry.
• Multiple installations of the lamps must have a minimum dis-
tance of 40 cm between centre of the shade of each unit.
• Keep a minimum of 30 cm distance from the walls and other
flammable or colour-sensitive objects.
• Keep the packaging if you intend to store your appliance in
the future.
Preparation before installation
CAUTION! Before installation, check the appliance to make
sure there is no damage. CLOSE the electrical power circuit
system & switch OFF the appliance before starting installation
work.
ATTENTION! Installation work should be carried out by quali-
fied electrician. Contact your local authority for advice if have
question. DO NOT attempt to install, repair and maintenance
by yourself.
• Verify prior to installation that the ceiling can safely support
the appliance.
• Make sure that no electrical wires, water pipes, gas pipes or
other lines are located around the installation location.
• Consult a qualified contractor for assistance about the struc-
ture of the ceiling. This is to ensure that the installation is car-
ried out properly and safely.
• Switch OFF the appliance by pressing the switch (5) on the
appliance at the "0" position.
ATTENTION! Before starting the installation, make sure you
have all the tools such as screwdriver, electric drills, measur-
ing tape, marking pencil, wall anchors, wiring nuts, mounting
bracket with hook, etc. (All are not supplied) and make sure
they are well functioning.
Instruction for installation
ATTENTION! Make sure again all the electrical power system
circuit is CLOSED and the switch (5) of the appliance is at the
OFF (0) position.
A) Installation of the mounting bracket with hook (Not includ-
ed).
• Secure the mounting bracket with screws and wall anchors
provided.
• Feed the electrical wires from the ceiling through opening of
the mounting bracket.
B) Assemble the appliance with the hook.
• You can extend the power cord by twisting the cap cover (4)
if the internal wires of power cord (1) are too short for con-
nection.
• Please make sure the wires are connected to the correspond-
ing wires terminal of the power circuit system. The wires of
the power cord are coloured as below:
a) Blue = Neutral (N)
b) Brown = Live (L)
c) Green and yellow = Earth (E)
• Wrap the connected wires together with the electrical insula-
tion tape or wiring nuts (Both are not included).
• Hang the hole (1) of the appliance with the hook as provided on
the mounting bracket. (Not supplied).
IMPORTANT! Please make sure the appliance is secure and
correctly connected after installation.
Operating instructions
ATTENTION! Make sure the electrical power system circuit of
ceiling is CLOSED and switch OFF the hanging lamp at the "0"
position.
• First, screw in clockwise direction the shatterproof lamp (sup-
plied) securely inside the lamp holder.
• This appliance has a retractable power cord to about 150 cm
that allows the lamp height to be adjusted. Rotate the knob (3)
to set the length of the power cord as desired.
• Then, pull gently straight down on the shade to extend the cord
until the desired height is reached.
• Next, open the electrical power system circuit and switch ON
the appliance by pressing the switch (5) to the "I" position.
• Now, the lamp is light up and keep food warm process is
started.
CAUTION! RISK OF BURNS! HOT SURFACE! The lamp
•
shade (6) surface is very hot during use. Do not touch
it. Switch OFF the lamp & cool down before setting
the cord length.
IMPORTANT! Remember to keep at least 30cm distance from
the lighted bulb.
Cleaning & Maintenance
ATTENTION! Always disconnect the appliance from the elec-
trical mains and cool down before storage, cleaning & main-
tenance.
GB
9