Operation; Cleaning, Maintenance And Repairs - Ferm TCM1002 Gebrauchsanweisung

OPERATION

Fig.1
• Ensure that there is sufficient water in the water
reservoir (4) before starting work, i.e. enough to
allow the diamond blade to pass through the water.
During work activities, the water must be topped up
through the fill opening (6).
• Do not start work until the correct rotational speed
has been reached.
• Diamond blades may NEVER be exposed to sidelong
pressure! This can cause them to break. Flying pieces
act as missiles and are highly dangerous!
• Do not attempt to cut very small pieces of stone.
During work, always make sure that the entire sur-
face of the stone is resting on the work table. The
mitre guide (supplied) can be used to slide paving sto-
nes through the machine. Ensure that the paving
stone remains level, especially in the initial cutting
phase. Doing this prevents the blade from jolting
upwards during cutting.
• Do not overload your tools. Your work is carried out
better and safer within the given capacity range. Do
not cut other materials other than paving stones or
tiles.
• Meticulously maintain your tools. Keep your tools
sharp and clean in order to be able to work safely and
correctly. Follow the maintenance instructions and
the directions concerning replacement of the dia-
mond blade.
• Ensure that you stand in a safe position and always
keep your balance. Avoid unnatural bodily positions.
Be constantly on your guard. Use caution in everyt-
hing that you carry out. Be sensible at work. Do not
use the machine if you are not able to concentrate or
if you are tired.
CUTTING GUIDE
Fig.1
It is possible to cut parallel to another guiding edge using
the cutting guide (3).
Adjustment: undo the knobs (7) and adjust to the desired
distance. Retighten the knobs. The markings (8) indicate
the measurement.
MITRE ANGLE ADJUSTMENT
Fig.1
The mitre angle can be variably adjusted from 0° to 45°.
Undo the star-shaped knobs (5) and adjust the mitre
angle by tilting the table (1) upwards until the desired gra-
dient is reached. Finally, retighten the knobs (5).
4
CLEANING, MAINTENANCE AND
REPAIRS
• Remove the plug from the wall socket after use and
before cleaning the machine, replacing the diamond
blade or interchanging the water reservoir.
• The machine is cleaned immediately after use as fol-
lows:
a. Remove the plug from the wall socket.
b. Remove the water reservoir from the machi
ne and allow the dirty water to drain away.
c. Unscrew the water splashback cover and
clean this.
d. Undo the star-shaped knobs, fold the table
upwards and clean the entire machine.
• The machine complies with the current safety pre-
conditions. All repair work may only be performed
by a recognised company as unauthorised repair
attempts can carry the risk of injury to the user or to
bystanders. Regularly check the plug and cable and
allow these to be replaced by a recognised company
in the event of damage to either. Likewise, check the
extension cables. Damaged safety facilities and
switches should, in the correct manner, be replaced
in order to continue using the machine.
CHECKING AND REPLACING THE DIA-
MOND BLADE
• Diamond blades that are cracked or distorted should
be replaced.
• Type of blade: 150 mm diameter diamond blade.
• Diamond blades which do not comply with the speci-
fications laid down in this instruction manual may not
be used.
• The plug should be removed from the wall socket
before changing the blade and adjustment or cleaning
activities.
• Care should be taken to ensure that the diamond
blade is fitted securely and rotates in the correct
direction.
• To replace a worn blade you should proceed as fol-
lows (fig. 2):
a. Remove the plug from the wall socket.
b. Remove the water reservoir (4, fig. 1) from
the machine.
c. Undo and remove the attachment bolts for
the splashback cover.
d. Undo the nut which holds the blade in place
(4, fig. 2).
e. Remove the blade (2, fig. 2) and slide the
new blade onto the flange (1, fig. 2). Take care
to observe the direction of rotation which is
indicated by an arrow on the blade. Next, refit
the counterflange (3, fig. 2).
f. Retighten the nut which holds the blade in
place (4, fig. 2) and refit the water splashback
cover.
g. Be sure that you do not leave any tools
behind the water splashback cover.
èË ˝ÍÒÔÎÛ‡Ú‡ˆËË ˝ÎÂÍÚ˘ÂÒÍËı χ¯ËÌ ‚Ò„‰‡
Òӷ≇ÈÚ ‰ÂÈÒÚ‚Û˛˘Ë Ô‡‚Ë· ÚÂıÌËÍË
·ÂÁÓÔ‡ÒÌÓÒÚË ‰Îfl ÒÌËÊÂÌËfl ËÒ͇ ÔÓʇ‡,
ÔÓ‡ÊÂÌËfl ˝ÎÂÍÚ˘ÂÒÍËÏ ÚÓÍÓÏ Ë Ú‡‚Ï.
èÓ˜ËÚ‡ÈÚ ̇ÒÚÓfl˘Ë Ú·ӂ‡ÌËfl, ‡ Ú‡ÍÊÂ
‚ıÓ‰fl˘Û˛ ‚ ÍÓÏÔÎÂÍÚ ËÌÒÚÛÍˆË˛ ÔÓ ÚÂıÌËÍÂ
·ÂÁÓÔ‡ÒÌÓÒÚË.
ï‡ÌËÚ ËÌÒÚÛ͈ËË ‚ ÏÂÒÚÂ, Ó·ÂÒÔ˜˂‡˛˘ÂÏ
Ëı ÒÓı‡ÌÌÓÒÚ¸!
èêÄÇàãÄ íÖïçàäà ÅÖáéèÄëçéëíà
• èÂ‰ ̇˜‡ÎÓÏ ‡·ÓÚ˚ ÌÛÊÌÓ Û·Â‰ËÚ¸Òfl ‚
ÓÚÒÛÚÒÚ‚ËË ÔÓ‚ÂʉÂÌËÈ Ì‡ ÒÚ‡ÌÍÂ, ÓÒÓ·ÂÌÌÓ Ì‡
ÂÊÛ˘ÂÏ ‰ËÒÍÂ. ÇÒ ˜‡ÒÚË ‰ÓÎÊÌ˚ ·˚Ú¸
Ô‡‚ËθÌÓ ÛÒÚ‡ÌÓ‚ÎÂÌ˚
ÛÒÎÓ‚ËflÏË ‰Îfl Ó·ÂÒÔ˜ÂÌËfl ÓÔÚËχθÌÓÈ ‡·ÓÚ˚
ÒÚ‡Ì͇. èË ÔÓ‰ÓÎÊËÚÂθÌÓÏ ÂÊËÏ ‡·ÓÚ˚
ÒΉÛÂÚ ÔÓ‚ÂflÚ¸
‡·ÓÚÓÒÔÓÒÓ·ÌÓÒÚ¸ ËÁ̇¯Ë‚‡ÂÏ˚ı ËÎË Ò΄͇
ÔÓ‚ÂʉÂÌÌ˚ı ‰ÂÚ‡ÎÂÈ
ÔËÒÔÓÒÓ·ÎÂÌËÈ. ùÚÓ
ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò ‚˚¯ÂÛÔÓÏflÌÛÚ˚ÏË ÛÒÎÓ‚ËflÏË.
Ñ‚ËÊÛ˘ËÂÒfl ˜‡ÒÚË - ÓÒÓ·ÂÌÌÓ Á‡˘ËÚÌ˚È ÍÓÊÛı
‰ËÒ͇ - ‰ÓÎÊÌ˚ ·˚Ú¸ Ô‡‚ËθÌÓ Á‡ÙËÍÒËÓ‚‡Ì˚ Ë
Ì ‰ÓÎÊÌ˚ Á‡Â‰‡Ú¸. á‡Ô¢‡ÂÚÒfl ËÒÔÓθÁÓ‚‡Ú¸
ÒÚ‡ÌÓÍ ·ÂÁ ÍÌÓÔÓÍ ‚Íβ˜ÂÌËfl-ÓÚÍβ˜ÂÌËfl.
• á‡Ô¢‡ÂÚÒfl ÒÌËχڸ Á‡˘ËÚÌ˚È ÍÓÊÛı ËÎË
‰ÓÔÓÎÌËÚÂθÌÓ ÙËÍÒËÓ‚‡Ú¸ Â„Ó Í‡ÍËÏË-ÚÓ
ÔËÒÔÓÒÓ·ÎÂÌËflÏË. á‡ÍÎËÌË‚¯ËÈ ÍÓÊÛı ÒΉÛÂÚ
ÌÂωÎÂÌÌÓ ÓÚÂÏÓÌÚËÓ‚‡Ú¸.
ìëíÄçéÇäÄ à
èãàíäéêÖáÄ
• ëÚ‡ÌÓÍ ÏÓÊÌÓ ËÒÔÓθÁÓ‚‡Ú¸
ÒÚ‡ˆËÓ̇ÌÓÏ ÂÊËÏÂ, Á‡ÙËÍÒËÓ‚‡‚ Â„Ó Í
Ó‚ÌÓÈ „ÓËÁÓÌڇθÌÓÈ ÔÓ‚ÂıÌÓÒÚË ˜ÂÂÁ
ÓÚ‚ÂÒÚËfl ‚ ÌËÊÌÂÈ ˜‡ÒÚË ÒÚ‡Ì͇.
• ç‡ÔflÊÂÌË ÒÂÚË ˝ÎÂÍÚÓÔËÚ‡ÌËfl ‚ ÓÁÂÚÍ ‰Îfl
ÔÓ‰Íβ˜ÂÌËfl ÒÚ‡Ì͇ ‰ÓÎÊÌÓ ·˚Ú¸ 230 Ç Ò
Á‡ÁÂÏÎÂÌËÂÏ Ë Á‡˘ËÚÓÈ
ÔÂ˚‚‡ÚÂÎÂÏ ˆÂÔË.
‰ÓÎÊÌÓ ÒÓÓÚ‚ÂÚÒÚ‚Ó‚‡Ú¸ ‚Â΢ËÌÂ, Û͇Á‡ÌÌÓÈ Ì‡
Á‡‚Ó‰ÒÍÓÈ Ú‡·Î˘ÍÂ.
• á‡Ô¢‡ÂÚÒfl ÓÚÒÓ‰ËÌflÚ¸ ‚ËÎÍÛ ÓÚ Ì‡ÒÚÂÌÌÓÈ
ÒÂÚ‚ÓÈ ÓÁÂÚÍË ‚˚Úfl„Ë‚‡ÌËÂÏ Á‡ ÒÂÚ‚ÓÈ ¯ÌÛ.
òÌÛ ÒΉÛÂÚ Á‡˘Ë˘‡Ú¸
ËÒÚÓ˜ÌËÍÓ‚ ÚÂÔ·, ÓÚ Ï‡Ò· Ë ÓÒÚ˚ı Ô‰ÏÂÚÓ‚.
ÑÎfl ‚‡¯ÂÈ
‡Á¯‡ÂÚÒfl ÔËÏÂÌflÚ¸
Á‡Ô˜‡ÒÚË Ë ÔËÒÔÓÒÓ·ÎÂÌËfl, ÍÓÚÓ˚ ÔÂ˜ËÒÎÂÌ˚ ‚
‰‡ÌÌÓÈ ËÌÒÚÛ͈ËË
ÔÓËÁ‚Ó‰ËÚÂÎÂÏ Ï‡¯ËÌ˚. Ç ÔÓÚË‚ÌÓÏ ÒÎÛ˜‡Â Ç˚ Ò‡ÏË
ÔÓ‰‚Â„‡ÂÚÂÒ¸ Ë ÔÓ‰‚Â„‡ÂÚ ‰Û„Ëı ËÒÍÛ ÔÓÎÛ˜ÂÌËfl
Ú‡‚Ï˚.
Ferm Ferm
êÄÅéíÄ çÄ ëíÄçäÖ
Fig.1
• èÂ‰ ̇˜‡ÎÓÏ ‡·ÓÚ˚ Ó·ÂÒÔ˜¸Ú ̇΢ËÂ
‰ÓÒÚ‡ÚÓ˜ÌÓ„Ó ÍÓ΢ÂÒÚ‚‡ ‚Ó‰˚ ‚ ·‡˜Í (4) Ú‡Í,
˜ÚÓ·˚ ÌËÊÌflfl
ÔÓ„Ûʇ·Ҹ ‚ ÌÂÂ. èÓ‰ÎË‚ ‰Â·ÂÚÒfl ˜ÂÂÁ
ÒÔˆˇθÌÓ ÓÚ‚ÂÒÚË (6) ÔË ‡·ÓÚÂ.
• ç ̇˜Ë̇ÈÚ ‡·ÓÚÛ, ÔÓ͇ ‰ËÒÍ Ì ‰ÓÒÚË„ÌÂÚ
‰ÓÎÊÌÓÈ ÒÍÓÓÒÚË ‚‡˘ÂÌËfl.
• á‡Ô¢‡ÂÚÒfl ÔËÍ·‰˚‚‡Ú¸ Í ÂÊÛ˘ÂÏÛ ‰ËÒÍÛ
·ÓÍÓ‚Ó ‰‡‚ÎÂÌËÂ, Ú‡Í Í‡Í ˝ÚÓ ÏÓÊÂÚ ÔË‚ÂÒÚË Í
ÔÓÎÓÏÍ ‰ËÒ͇ Ë Ì‡ÌÂÒÂÌ˲ ۂ˜ËÈ ÓÚÎÂÚ‚¯ËÏË
ÓÒÍÓÎ͇ÏË.
‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò
• ç ÒΉÛÂÚ ÂÁ‡Ú¸ Ó˜Â̸ χÎÂ̸ÍË Ô‰ÏÂÚ˚.
èË ‡·ÓÚ ‚Òfl ÔÎÓÒÍÓÒÚ¸ ÔÎËÚÍË ‰ÓÎÊ̇
ÓÔË‡Ú¸Òfl ̇ ÔÓ‚ÂıÌÓÒÚ¸ ÒÚÓ· ÒÚ‡Ì͇; ÔË ˝ÚÓÏ
ËÒÔ‡‚ÌÓÒÚ¸ Ë
̇Ô‡‚Îfl˛˘‡fl ÍÓÒÓ„Ó ÂÁ‡
ÔÓ‰‚ËÊÂÌËfl ÔÎËÚÍË ÔË ÂÁÍÂ. Ç Ì‡˜‡Î ÂÁÍË
Ë Á‡˘ËÚÌ˚ı
̇‰Ó ÔÎÓÚÌÓ Ôˉ‡‚ÎË‚‡Ú¸ ÔÎËÚÍÛ Í ÒÚÓÎÛ ‚Ó
‚˚ÔÓÎÌflÂÚÒfl ‚
ËÁ·ÂʇÌË Ò͇˜Í‡ ‰ËÒ͇.
• ç ÔÂ„ÛʇÈÚ ҂ÓÈ ÒÚ‡ÌÓÍ. ꇷÓÚ‡ ·Û‰ÂÚ
·ÓΠÔÓ‰ÛÍÚË‚ÌÓÈ Ë ·ÂÁÓÔ‡ÒÌÓÈ ‚ Ô‰Â·ı „Ó
ÏÓ˘ÌÓÒÚË. ç ËÒÔÓθÁÛÈÚ ËÌ˚Â, ÌÂÊÂÎË
Ó„Ó‚ÓÂÌÌ˚ ‡ÌÂÂ, χÚÂˇÎ˚ ‰Îfl ÂÁÍË.
• í˘‡ÚÂθÌÓ Ûı‡ÊË‚‡ÈÚ Á‡ Ò‚ÓËÏ ÒÚ‡ÌÍÓÏ,
‚Ó‚ÂÏfl Á‡Ú‡˜Ë‚‡ÈÚ ÂÊÛ˘Ë ˜‡ÒÚË, ÒÓ‰ÂÊËÚÂ
ËÌÒÚÛÏÂÌÚ ‚ ˜ËÒÚÓÚ ‰Îfl Â„Ó Ô‡‚ËθÌÓÈ Ë
·ÂÁÓÔ‡ÒÌÓÈ ‡·ÓÚ˚. ëӷ≇ÈÚ ÂÍÓÏẨ‡ˆËË
ÔÓ ÛıÓ‰Û Ë Á‡ÏÂÌ ÂÊÛ˘Â„Ó ‰ËÒ͇.
• LJ¯Â ÔÓÎÓÊÂÌËÂ Ë ÔÓÁ‡ ÔË ‡·ÓÚ ‰ÓÎÊÌ˚ ·˚Ú¸
çÄëíêéâäÄ
·ÂÁÓÔ‡ÒÌ˚ÏË
ÂÒÚÂÒÚ‚ÂÌÌ˚ÏË. ç ÓÚ‚ÎÂ͇ÈÚÂÒ¸ ÔË ‡·ÓÚÂ,
ÔÓÒÚÓflÌÌÓ ·Û‰¸Ú ‚ÌËχÚÂθÌ˚Ï; Òӷ≇ÈÚÂ
ÚÓθÍÓ Í
ÓÒÚÓÓÊÌÓÒÚ¸. ç ÔËÒÚÛÔ‡ÈÚÂ Í ‡·ÓÚÂ, ÂÒÎË Ç˚
˜Û‚ÒÚ‚ÛÂÚÂ
ÒÍÓ̈ÂÌÚËÓ‚‡Ú¸Òfl.
èÄêÄããÖãúçÄü çÄèêÄÇãüûôÄü
Fig.1
‡‚ÚÓχÚ˘ÂÒÍËÏ
ç‡ ÒÚ‡ÌÍ ÏÓÊÌÓ ÂÁ‡Ú¸ ÎËÌ˲ Ô‡‡ÎÎÂθÌÓ Í‡ÍÓÈ-ÚÓ
ëÂÚ‚Ó ̇ÔflÊÂÌËÂ
ÍÓÏÍ (‰Û„ÓÈ ÎËÌËË) Ò ÔÓÏÓ˘¸˛ ̇Ô‡‚Îfl˛˘ÂÈ
(3). ÑÎfl ˝ÚÓ„Ó ÓÚ‚ÂÌËÚ ÛÍÓflÚÍË (7), ÛÒÚ‡ÌÓ‚ËÚÂ
ÌÛÊÌÓ ‡ÒÒÚÓflÌËÂ Ë Á‡ÚflÌËÚ Ëı. êËÒÍË Ì‡ ÎËÌÂÈÍÂ
(8) ÔÓ͇Á˚‚‡˛Ú ‚Â΢ËÌÛ ‡ÒÒÚÓflÌËfl.
ÓÚ ‚ÓÁ‰ÂÈÒÚ‚Ëfl
êÖÉìãàêéÇäÄ ìÉãÄ éëà êÖáÄ
Fig.1
ì„ÓÎ ÓÒË ÂÁ‡ ÏÓÊÌÓ ÛÒÚ‡ÌÓ‚ËÚ¸ ÓÚ 0° ‰Ó 45°.
΢ÌÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË
éÚÍÛÚËÚ ÛÍÓflÚÍË-·‡‡¯ÍË (5) Ë ÛÒÚ‡ÌÓ‚ËÚÂ
ÚÓθÍÓ ÚÂ
ÌÛÊÌ˚È Û„ÓÎ ÔÓ‰˙ÂÏÓÏ ÒÚÓ· (1) ‚‚Âı. ÇÌÓ‚¸
Á‡ÚflÌËÚ ÛÍÓflÚÍË (5).
ÎË·Ó ÂÍÓÏẨӂ‡Ì˚
˜‡ÒÚ¸ ÂÊÛ˘Â„Ó ‰ËÒ͇
ËÒÔÓθÁÛÂÚÒfl ‰Îfl
Ë ‚Ò„‰‡ ÛÒÚÓȘ˂˚ÏË Ë
ÛÒÚ‡ÎÓÒÚ¸ Ë Ì ÏÓÊÂÚÂ
29