Hitachi CL32W35TAN Serviceanleitung Seite 53

Test Point Net Name
TP203 /1EEE1394_RESET
TP219 /OFFHOOK
TP249 /PALENC_AV_RESET
TP248 NVM_WP#
TP995 22KHZ_EN
TP216 TS/NPES
TP1105 ROM_SIZE
TP233 /TS
TP1152 GNDD
TP1041 USER_RESET
TP221 /RESET
TP244 MPEG_RESET
TP1097 USER_RESET
TP217 /USER_RESET_B
TP1113 SC_DET_B
TP1104 SC0_C4
TP1103 SC_RST0
TP1075 SC_DETECT0
TP1081 SC_CLK0
TP1102 SC0_C8
TP1037 /CS_EPROM
TP1052 /OE_ROM
TP1151 GNDD
TP227 RY/NBY1
TP228 RY/NBY0
TP1100 /CS_FLASH0
TP1048 /CS_FLASH1
TP232 SC1_I/O
TP250 /CS_008
TP251 /BREQ
TP252 /BGACK
TP253 /INT_CI1
TP255 /INT_1EEE1394
TP258 /INT_CI2
TP259 /INT_DRAMC
TP260 /DMACK
TP261 /RESET
TP1156 ACLK
TP1150 /DMREQ
TP231 /CS0
TP1106 /CS1
TP204 /STROBE
TP210 /AUTOFD
TP202 /INIT
TP209 /SELECTIN
TP269 1394OUT7
TP208 /1394OVAL
TP207 BUSY
TP206 PERROR
TP205 SELECT
TP200 /NFAULT
TP230 MODEM_DTR
TP236 MODEM_CTS
TP237 MODEM_DSA
TP238 MODEM_TO_CPU
TP239 CPU_TO_MODEM
TP240 MODEM_RTS
TP241 RS232_RX
TP242 RS232_TX
TP1063 RS232_RTS
TP1062 RS232_CTS
TP293 PD_A4
TP292 PD_A5
Function
/1EEE1394_RESET
Not off hook detect
PAL encoder reset
NVM write protect
22KHZ enable pin
Transport stream select
ROM_SIZE
Packet elemental stream select
Digital ground
USER_RESET (from IPL)
Not MPEG reset
MPEG_RESET
base drive for user reset (from IPL)
Not user reset (from IPL)
Smart card detect B
Smart card output 4
Smart card reset
Smart card detect O
Smart card clock output
Smart card output 8
Not chip select eprom
Not ROM output enable
Digital Ground
Ready/ not Busy Flash 1
Ready/ not Busy Flash 0
Not flash chip select 0
Not flash chip select 1
Smart card input/output 1
Not chip select 008
Bus request
Bus Grant acknowledge
Interupt common interface 1
Interupt IEEE1394
Interupt common interface 2
Interupt DRAM controller
DMA acknowledge
Not reset
Oversampling clock
DMA request
Not Chip select 0
Not Chip select 1
IEEE1284/IEEE1394 data strobe
IEEE1284 general purpose control
IEEE1284 peripheral initialisation
IEEE1284 peripheral selection indicator
1394 OUTPUT 7
Not 1394 output valid
IEEE1284 peripheral busy
IEEE1284 peripheral error
IEEE1284/IEEE1394 peripheral select
IEEE1284 peripheral fault
Modem Data terminal ready
Modem clear to send
Modem Data set ready
Modem to CPU data
CPU to modem data
Modem ready to send
RS232 receive
RS232 transmit
RS232 ready to send
RS232 clear to send
DRAM address 4
DRAM address 5
52