Unpacking; Assembly - Parkside PBLS 26 A1 Bedienungs- Und Sicherheitshinweise

Noise can have serious effects on your health. If the device
noise exceeds 85 dB (A), please wear suitable hearing pro-
tection.
Noise
Sound pressure level L .................................................... 87 dB
pA
Uncertainty K .................................................................... 3 dB
pA
Sound power level L ....................................................107 dB
WA
Uncertainty K ..............................................................1.87 dB
WA
Guaranteed Sound power level L
Wear hearing protection.
Excessive noise can result in a loss of hearing.
The specified device emissions values have been measured in
accordance with a standardised test procedure and can be
used for the comparison of one tool with another.
The specified noise emission values can also be used for an
initial estimation of the exposure.
Vibration
Top handle....................................................................5.28 m/s
Bottom handle ............................................................. 5.56 m/s
Uncertainty K ................................................................. 1.5 m/s
Keep the noise level and vibration to a minimum!
• Only use devices which are free of defects.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.
• Wear gloves.
WARNING
Avoid the risks associated with vibration, e.g. the risk of white
finger syndrome (circulatory disorders) by taking frequent
breaks from work where you rub your palms together, for ex-
ample.
• Always wear protective gloves and make sure your hands
are warm.
• Take regular breaks from work.

8. Unpacking

• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, keep the packaging until the expiry of the war-
ranty period.
m DANGER
The device and the packaging are not children's
toys! Do not let children play with plastic bags,
films or small parts! There is a danger of choking
or suffocating!
26 GB
...............................109 dB
WA
2
2
2

9. Assembly

The device can be used both as a petrol leaf blower and as a
petrol leaf vacuum. It is necessary to set up the device in ac-
cordance with the respective purpose.
Note
Always set up the device on a level and stable surface.
9.1 Leaf blower assembly (Fig. 2 + 3)
9.1.1 Fit the blast pipe (4) to the motor unit (10)
(Fig. 2):
1. Remove the locking screw (5) on the blast connection (6)
of the motor unit (10).
2. Align the attachment point (A) of the blast pipe (4) with
the projection (B) of the blowgun (6).
3. Slide the blast pipe (4) into the blasting connection (6).
4. Retighten the locking screw (5).
9.1.2 Fit the flat nozzle (1) / round nozzle (2) to
the blast pipe (4) (Fig. 3):
The petrol leaf blower can be operated with a flat nozzle (1)
or a round nozzle (2).
1. Align the flat nozzle (1) / round nozzle (2) with the pro-
jection (C) of the blast pipe (4).
2. Push the flat nozzle (1) / round nozzle (2) and the blast
pipe (4) together and turn them 90° clockwise.
3. Tighten the locking screw (3).
Note
The petrol leaf blower is correctly mounted when the flat noz-
zle (1) / round nozzle (2) points towards the ground.
Note
The petrol leaf blower cannot be started if the blast pipe (4)
is not fitted.
9.2 Leaf vacuum assembly (Fig. 4 - 9)
m CAUTION:
Always make sure the device is fully assembled
before commissioning!
9.2.1 Fit the vacuum tube (14) to the motor unit
(10) (Fig. 4, 5):
1. Open the protective grille (11) by sliding the catch (D) to the
side. Use a suitable tool for this (e.g. a slotted screwdriver).
2. Fold open the protective grille (11).
3. Fit the vacuum tube (14) to the vacuum connection (29).
The grooves (E) in the vacuum tube (14) must match the
pins on the vacuum connection (29).
4. Turn the vacuum tube (14) clockwise as far as it will go to
secure the vacuum tube (14).
9.2.2 Fit the suction nozzle (12) to the vacuum
tube (14) (Fig. 6):
1. Align the suction nozzle (12) with the pin (F) of the vac-
uum tube (14).
2. Push the suction nozzle (12) and the vacuum tube (14)
together and turn them 90° clockwise.
3. Tighten the locking screw (13).