Makita UR014G Betriebsanleitung Seite 16

ASSEMBLY
WARNING:
Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
WARNING:
Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Installing the handle
1.
Attach the upper and lower clamps on the damper.
2. Put the handle on the upper clamp and fix it with
hex socket head bolts as illustrated.
► Fig.10: 1. Hex socket head bolt 2. Handle 3. Upper
clamp 4. Damper 5. Lower clamp
Hex wrench storage
CAUTION:
Be careful not to leave the hex
wrench inserted in the tool head. It may cause
injury and/or damage to the tool.
When not in use, store the hex wrench as illustrated to
keep it from being lost.
► Fig.11: 1. Hex wrench
Installing the cutting tool
CAUTION:
Always use the supplied wrenches
to remove or to install the cutting tool.
CAUTION:
Be sure to remove the hex wrench
inserted into the tool head after installing the
cutting tool.
NOTE: The type of the cutting tool(s) supplied as
the standard accessory varies depending on the
countries. The cutting tool is not included in some
countries.
NOTE: Turn the tool upside down so that you can
replace the cutting tool easily.
Nylon cutting head
NOTICE:
Be sure to use genuine Makita nylon
cutting head.
1. Insert the hex wrench through the hole in the gear
case to lock the spindle. Rotate the spindle until the hex
wrench is fully inserted. Remove the nut by turning it
clockwise with the box wrench.
► Fig.12: 1. Nut 2. Hex wrench
2. Remove the spool holder by pressing the claws.
► Fig.13: 1. Spool holder 2. Claw
3. Remove the spool from the spool holder by holding
the nylon cord with your fingers and thumb, and then hook
both sides of the nylon cord to the notches of the spool.
► Fig.14: 1. Spool 2. Spool holder 3. Notch
4. Insert the hex wrench through the hole in the gear
case to lock the spindle. Attach the spool holder to the
spindle, and then tighten the nut by turning it counter-
clockwise with the box wrench.
► Fig.15: 1. Nut 2. Spool holder 3. Hex wrench
NOTE: The recommended tightening torque is 20 to
30 N•m.
5.
Attach the spool to the spool holder, and then set
both sides of the nylon cord to the eyelets of the spool
holder. Attach the spool cover to the spool holder.
► Fig.16: 1. Spool 2. Spool holder 3. Eyelet 4. Spool
cover
6. Remove the hex wrench from the gear case.
Correct combination of the cutting
tool and the protector
CAUTION:
Always use the correct combi-
nation of cutting tool and the protector. A wrong
combination may not protect you from the cutting tool,
flying debris, and stones. It can also affect the bal-
ance of the tool and result in an injury.
Cutting tool
Nylon cutting head
Installing the protector
WARNING:
guard illustrated in place. Failure to do so can
cause serious personal injury.
CAUTION:
Take care not to injure yourself on
the cutter for cutting the nylon cord.
Attach the protector to the clamp using bolts.
► Fig.17: 1. Clamp 2. Protector 3. Cutter
OPERATION
Attaching the shoulder harness
WARNING:
control of the tool at all times. Do not allow the
tool to be deflected toward you or anyone in the
work vicinity. Failure to keep control of the tool
could result in serious injury to the bystander and the
operator.
16 ENGLISH
Protector
Never use the tool without the
Be extremely careful to maintain