Makita UR013G Betriebsanleitung Seite 19

Overdischarge protection
When the battery capacity becomes low, the tool stops
automatically and the caution lamp starts blinking in red.
If the tool does not operate even when the switches are
operated, remove the battery cartridge from the tool and
charge it.
Indicating the remaining battery
capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
► Fig.6: 1. Indicator lamps 2. Check button
Indicator lamps
Lighted Off
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
NOTE: The first (far left) indicator lamp will blink when
the battery protection system works.
Main power switch
To turn on the tool, press the main power button. To turn
off the tool, press and hold the main power button until
the main power lamp goes off.
► Fig.7: 1. Main power lamp 2. Main power button
NOTE: The tool will automatically turned off if it is left
without any operations for a certain period of time.
Switch action
WARNING:
For your safety, this tool is
equipped with lock-off lever which prevents the
tool from unintended starting. NEVER use the tool
if it runs when you simply pull the switch trigger
without pressing the lock-off lever. Return the
tool to our authorized service center for proper
repairs BEFORE further usage.
WARNING:
NEVER tape down or defeat pur-
pose and function of lock-off lever.
Remaining
capacity
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released. Operating a tool
with a switch that does not actuate properly can lead
to loss of control and serious personal injury.
CAUTION:
Never put your finger on the main
power button and switch trigger when carrying
the tool. The tool may start unintentionally and cause
injury.
NOTICE:
Do not pull the switch trigger hard with-
out pressing the lock-off lever. This can cause
switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided. To start the tool,
depress the lock-off lever and pull the switch trigger.
Release the switch trigger to stop.
► Fig.8: 1. Lock-off lever 2. Switch trigger
Speed adjusting
You can adjust the tool speed using the adjusting lever.
To adjust the tool speed, move the lever while depress-
ing the lock-off lever and pulling the switch trigger.
To increase the speed, move the lever downward. To
decrease the speed, move the lever upward. When the
adjusting lever is in the uppermost position, the tool
stops.
► Fig.9: 1. Adjusting lever
Reverse button for debris removal
WARNING:
the battery cartridge before you remove entan-
gled weeds or debris which the reverse rotation
function can not remove. Failure to switch off and
remove the battery cartridge may result in serious
personal injury from accidental start-up.
This tool has a reverse button to change the direction of
rotation. It is only for removing weeds and debris entan-
gled in the tool.
To reverse the rotation, press the reverse / high-torque
button when the cutting tool is stopped. The cutting tool
rotates in reverse direction and the reverse lamp blinks
when you pull the switch trigger while depressing the
lock-off lever.
To return to regular rotation, release the trigger and wait
until the cutting tool stops.
► Fig.10: 1. Reverse lamp 2. Reverse / high-torque
button
NOTE: During the reverse rotation, the tool operates
only for a short period of time and then automatically
stops.
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
NOTE: If you press the reverse / high-torque button
while the cutting tool is still rotating, the tool comes to
stop and to be ready for reverse rotation.
19 ENGLISH
Switch off the tool and remove