Mounting And Operation; Working Advice - Bosch AdvancedAquatak 150 Originalbetriebsanleitung

Mounting and Operation

Representation/Action Ob-
jective
Delivery scope Advan-
cedAquatak 150
Adjusting the Handle
Connecting high pressure wa-
ter supply hose/nozzle
Connecting to the water supply
Starting
Stopping
Clean both filters
Clean nozzle
Connecting high pressure gun
to lance
Attaching Nozzle
Connect detergent bottle
Gun storage
Storage
Transport
Selecting accessories
Switching on
For Your Safety
Warning: Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). If in doubt contact a quali-
fied electrician or the nearest Bosch Service Centre.
For products not sold in GB:
Warning: For your safety, it is required that the plug at-
tached to the product is connected with the extension cord.
The coupling of the extension cord must be protected
against splash water, be made of rubber or coated with rub-
ber. The extension cord must be used with a cable strain re-
lief.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Bosch Power Tools
Operation
To prevent damage to the appliance, do not allow it to op-
u
Figure Page
erate dry.
A 31
Starting
Attach water supply hose (not supplied) to the mains water
B 32
supply and machine.
C 32 Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
D 33
Press the safety lock (back button on the gun handle) to re-
E 34
lease the trigger. Fully press the trigger until there is a con-
F 34
stant flow of water to clear the air from the machine and wa-
G 35 ter supply hose. Release trigger. Press the safety lock (front
button on the gun handle).
H 35
Turn button on main switch. Point the power gun down-
I 36
wards. Press the trigger safety lock to release the trigger.
Fully press the trigger.
J 36
Autostop Function
K 37
The machine is designed to switch off the motor when the
L 38
trigger is released on the gun.
M 38
N 39

Working Advice

O 40
General
Never use a roto nozzle or pencil jet to clean motor
u
vehicles.
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the
pressure washer by pulling the hose, this could cause the
ma-chine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high pressure
hose. Do not expose the high pressure hose to sharp edges
or corners.
Working advice for cleaning with detergents
Only use cleaning agents suitable specifically for high
u
pressure washers.
Detergents must not be used undiluted. The products are
u
safe to use as they contain no acids, alkalis or substances
which are detrimental to the environment. We recom-
mend that the detergents are kept out of the reach of chil-
dren. If detergent comes into contact with the eyes, wash
immediately with plenty of water and if swallowed contact
a doctor immediately.
Comply with the application, disposal and warning in-
u
structions of the detergent manufacturers.
We recommend using cleaning agent sparingly in the interest
of environmental protection. Observe the recommended di-
lution on the detergent label.
Recommended cleaning method
Step 1: Attach the fixed fan nozzle and remove the heavy
dirt.
English | 13
F 016 L94 561 | (18.11.2022)