Mounting And Operation - Bosch AdvancedAquatak series Originalbetriebsanleitung

Vibration total values a (triax vector sum) and uncertainty K determined according to EN 60335-2-79
h
– Vibration emission value a
h
– Uncertainty K

Mounting and Operation

Action
Delivery scope
Adjusting the Handle
Connecting high pressure wa-
ter supply hose/nozzle
Connecting to the water supply
Switching On and Off
Clean the water filter
Clean nozzle
Connecting high pressure gun
to lance
Tube Assembly
Connect detergent bottle
Variable Fan lance
Connecting high pressure gun
to lance
Adjust water jet
Roto lance
Connecting high pressure gun
to lance
Adjust water jet
Gun storage
Storage
Transport
Selecting Accessories
Switching on
For Your Safety
Warning: Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
The operating voltage is 230 V AC, 50 Hz (for non-EU coun-
tries 220 V, 240 V as applicable). Contact your Bosch Ser-
vice Centre for details. If in doubt contact a qualified electri-
cian or the nearest Bosch Service Centre.
If you want to use an extension cable when operating your
high pressure washer, only the following cable dimensions
should be used:
2
– 2.5 mm – max length 25 m
Note: If an extension cable is used it must be earthed and
connected through the plug to the earth cable of your supply
network in accordance with prescribed safety regulations.
Bosch Power Tools
If in doubt contact a qualified electrician or the nearest
Bosch Service Centre.
Figure Page
A 281
B 282
and intended for outdoor use.
C 282
The connections (plugs and sockets) should be kept dry and
off the ground.
For increased electrical safety use a Residual Current Device
D 283
(RCD) with a tripping current of not more than 30 mA. Al-
E – F 283
ways check your RCD every time you use it.
G 284
If the supply cord is damaged, it must be replaced by a
H 284
Bosch Service Centre.
For products not sold in GB:
I 284
Warning: For your safety, it is required that the plug at-
tached to the product is connected with the extension cord.
J 285
The coupling of the extension cord must be protected
K 285
against splash water, be made of rubber or coated with rub-
L 286 ber. The extension cord must be used with a cable strain re-
lief.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
M 287
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
N 288
The severed plug must be disposed of to avoid a possible
O 288
shock hazard and should never be inserted into a mains
P 289
socket elsewhere.
Q 290
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Operation
To prevent damage to the appliance, do not allow it to
u
operate dry.
Starting
Attach water supply hose (not supplied) to the mains water
supply and machine.
Connect the product to the mains supply ensuring that the
mains switch is in the off position.
Open water tap.
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and wa-
ter supply hose. Release trigger. Press the safety lock (front
button on the gun handle).
Autogoods "130"
3 600 HA7 7..
2
m/s 3.2
2
m/s 1.0
WARNING! Inadequate extension cables can
be dangerous. Extension cable, plug and
socket must be of watertight construction
F 016 L81 291 | (04.03.2019)
English | 17
3 600 HA7 8..
2.9
1.0