Specifications; Specific Safety Rules - Makita 6805BV Betriebsanleitung

ENGLISH
1 Front cap
2 Locator
3 Pointer
4 Adjusting ring

SPECIFICATIONS

Model
Capacities
Self drilling screw ........................................... 6 mm
Machine screw ............................................... 8 mm
Wood screw ................................................ 6.2 mm
Bit shank size ............................................... 1/4" Hex
–1
No load speed (min ) ................................ 0 – 2,500
Overall length ................................................ 267 mm
Net weight ........................................................ 1.9 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated
adherence to screwdriver safety rules. If you use
this tool unsafely or incorrectly, you can suffer
serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
Explanation of general view
5 Low
6 High
7 Speed control screw
8 Switch trigger
6805BV
GEB017-1
use) replace strict
9
10 Reversing switch lever
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
OPERATING INSTRUCTIONS
Removing or installing the bit (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before removing or installing the bit.
To remove the bit, first pull the front cap off and then
pull the bit firmly. To install the bit, insert it into the
tool as far as it will go and then replace the front cap.
Depth adjustment (Fig. 2, 3 & 4)
When you wish to drive self drilling screws, etc.,
adjust the depth as follows. Turn the locator to adjust
the depth.
Initially, adjust the locator to create a distance of
approximately 1 mm from the tip of the front cap
(which works in conjunction with the locator) to the
base of the screw head. One full turn of the locator
equals 1 mm change in depth. After adjusting the
locator, turn the adjusting ring so that the 6" mark is
aligned with the pointer on the gear housing. Drive a
trial screw into your material or a piece of duplicate
material. If the depth is not suitable for the screw,
continue adjusting until the proper depth setting is
obtained.
Adjusting fastening torque (Fig. 5)
When you wish to drive tool screws, wood screws,
hex bolts, etc. with the predetermined torque, adjust
the fastening torque as follows. The fastening torque
may be adjusted by turning the adjusting ring. Before
turning the adjusting ring, turn the locator in the
direction of the arrow as far as it will go without forc-
ing. The torque is increased by turning the adjusting
ring in the direction of the arrow and decreased by
turning it in the opposite direction. Align the number 1
on the adjusting ring with the pointer on the gear
housing. Drive a trial screw into your material or a
piece of duplicate material. If the fastening torque is
not suitable for the screw, continue adjusting until the
proper torque is obtained.
CAUTION:
The adjusting ring should be turned only within the
numbered range. It should not be forced beyond this
range.
Lock button
3