Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
7 Setup and operation
7.1 Inserting the batteries
1. Remove the battery compartment cover (6).
2. Insert two AAA batteries (included). Ensure that the batteries are inserted with the correct
polarity. The positive and negative terminals are marked on the batteries and on the inside
of the battery compartment cover (6).
The product will switch on automatically and display the measured temperature and
Æ
humidity.
3. Replace the battery compartment cover (6).
7.2 Hanging/positioning the product
The product can be hung on a wall using the keyhole hanger (4) or placed on a solid surface
using the stand (8).
To hang the product on a wall, proceed as follows:
Ensure that no existing cables or pipes (including water pipes) are damaged when
drilling mounting holes or securing screws.
1. Install a suitable screw in the desired position and let it protrude a few millimetres from
the wall.
2. Then hang the product on the screw using the keyhole hanger. Handle the product with
care when hanging it on the wall.
To place the product on a level surface, proceed as follows:
1. Fold out the stand (8).
2. Place the product on a level, stable and sufficiently large surface.
Important:
– When placing the product on expensive furniture, use a suitable mat to prevent scratch
marks.
7.3 Selecting the temperature unit
1. Press the °C/°F toggle button (5).
The temperature display will change to °C or °F.
Æ
2. Press the °C/°F toggle button (5) again to switch back to the previous temperature unit.
7.4 Displaying maximum/minimum values
1. Press the MAX/MIN button (2) to display the maximum and minimum temperature values:
– Press 1x: Displays the maximum measured temperature and humidity
– Press 2x: Displays the minimum measured temperature and humidity
– Press 3x: Returns to the current readings
Note:
– If no other buttons are pressed, the display will automatically return to the current
readings after 5 seconds.
7.5 Reset maximum/minimum values
1. Press the MAX/MIN button (7) for 3 seconds.
The maximum/minimum values will be reset.
Æ
8 Cleaning and care
Important:
– Do not use any aggressive cleaning agents, rubbing alcohol or other chemical
solutions. These may damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Before cleaning, open the battery compartment cover (6) and remove the batteries.
2. Clean the product with a dry, lint-free cloth.
3. Insert the batteries again. Ensure that the batteries are inserted with the correct polarity.
The positive and negative terminals are marked on the batteries and on the inside of the
battery compartment cover (6).
4. Replace the battery compartment cover (6).
9 Disposal
9.1 Product
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set
up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.
9.2 (Rechargeable) batteries
Remove batteries/rechargeable batteries, if any, and dispose of them separately from the
product. According to the Battery Directive, end users are legally obliged to return all spent
batteries/rechargeable batteries; they must not be disposed of in the normal household waste.
Batteries/rechargeable batteries containing hazardous substances are labelled
with this symbol to indicate that disposal in household waste is forbidden. The
abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury,
Pb = Lead (name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our
stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations
and contribute to environmental protection.
Batteries/rechargeable batteries that are disposed of should be protected against short circuit
and their exposed terminals should be covered completely with insulating tape before disposal.
Even empty batteries/rechargeable batteries can contain residual energy that may cause them
to swell, burst, catch fire or explode in the event of a short circuit.
10 Technical data
10.1 Power supply
Power supply ................................ 2x 1.5 V AAA batteries (not included)
Current consumption .................... Max. 50 µA
Battery lifespan ............................. approx. 2 years
10.2 Measurement range
Temperature
measurement range ..................... -10 to +50 °C
Humidity measurement range ...... 20 – 95 % RH
10.3 Environment
Operating temperature ................. -10 to +50 °C
Operating humidity ....................... 20 – 99 % RH
Storage temperature ..................... -10 to +50 °C
Storage humidity ........................... 20 – 99 % RH
10.4 Other
Dimensions (Ø x H) ...................... Ø 94 x 20 mm
Weight .......................................... 110 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reflects the technical status at the time of printing.
Copyright 2022 by Conrad Electronic SE.
*2617740_v1_0922_02_DS_m_4L_(1)
Werbung
Inhaltsverzeichnis
