Taurus Alpatec Catala FACTOR CONNECT Bedienungsanleitung Seite 8

Downloaded by: pm-capetown on 27-10-2022 08:59 CEST
- Factor Connect is too far away from the router.
- The Wi-Fi password is incorrect.
USE:
- Extend the cable completely before plugging
it in.
- Connect the appliance to the mains.
- Turn on the power switch.
- Turn the appliance on, by using the on/off
button (1).
- The display (D) will show the ambient tempera-
ture and will start blowing cold air.
- Select the desired function
FAN FUNCTION:
- Press the function and power selector button
(2) until the fan function pilot light turns on and
the appliance blows cold air.
HEATER FUNCTION:
- Select the desired heating power by pressing
the function and power selection button (2).
- Use the adjustable thermostat button (7) to
select the desired temperature (10-35ºC).
TIMER FUNCTION:
- The appliance's operating time can be control-
led (1-24h)
- To program the operating time, press the timer
button (3). The display will show the pro-
grammed hours. To adjust the time, press the
adjustable timer button (7). For each time it is
pressed, the time will be adjusted by 1 hour.
- The time selected will be shown on the display
(D).
- When you reach the desired time, stop pres-
sing the button. After 5 seconds the display (D)
will show the ambient temperature again. This
means the time has been confirmed.
ECO MODE:
- This mode regulates the power of the applian-
ce by itself by comparing the ambient tempe-
rature and the temperature selected on the
thermostat. If the ambient temperature is closer
to the selected one, it will use less power If the
difference is large, it will use more power.
- To activate this mode, press the ECO button
(4).
SILENCE MODE:
- This mode reduces the operation noise signi-
ficantly.
- To activate this mode, press the silent button (5).
ONCE YOU HAVE FINISHED USING THE
APPLIANCE:
- Turn the appliance off, using the on/off button
(1). The appliance will cool itself for 30 seconds
before completely turning off.
- Unplug the appliance from the mains.
- Clean the appliance.
CARRY HANDLE:
- This appliance has a handle on the back (C) to
make it easy and convenient to transport.
ANTI-TIPPING SAFETY DEVICE:
- The appliance has an anti-tipping safety device
that turns it off if the working position is not the
correct one.
SAFETY THERMAL PROTECTOR:
- The appliance has a safety device, which pro-
tects the appliance from overheating.
- When the appliance switches itself on and
off repeatedly, for reasons other than the
thermostat control, check to ensure that there
are no obstacles that impede correct air entry
or expulsion.
- If the appliance turns itself off and does not
switch itself on again, disconnect it from the
mains supply, and wait for approximately 15
minutes before reconnecting. If the machine
does not start again seek authorised technical
assistance.
CLEANING
- Disconnect the appliance from the mains and
allow it to cool before undertaking any cleaning
task.
- Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or
base pH such as bleach, or abrasive products,
for cleaning the appliance.
- Do not let water or any other liquid get into the
air vents to avoid damage to the inner parts of
the appliance.
- Never submerge the appliance in water or any
other liquid or place it under running water.
- If the appliance is not in good condition of
cleanliness, its surface may degrade and
inexorably affect the duration of the appliance's
useful life and could become unsafe to use.
- Remark: When the appliance is used as a hea-
ter after long periods in storage or after having
been used solely as a fan a small amount of
smoke may be produced. This is not important