ChiQ MG80-14586BW Benutzerhandbuch Seite 3

INSTALLATION
The washer must be handled and installed by two or more persons – risk of injury. Use protective
•
gloves to unpack and install – risk of cuts.
The washer must be installed and operated in a room with the drain.
•
Installation, including water supply (if any) and electrical connections and repairs must be carried out by
•
a qualified technician. Keep children away from the installation site. After unpacking the washer, make
sure that it has not been damaged during transport. In the event of problems, contact the dealer or
your nearest After-Sales Service. Once installed, packaging waste (plastic, Styrofoam parts etc.) must be
stored out of reach of children – risk of suffocation. The washer must be disconnected from the power
supply before any installation operation – risk of electric shock. During installation, make sure the
washer does not damage the power cable – risk of fire or electric shock. Only activate the washer when
the installation has been completed.
Do not install the washer where it may be exposed to extreme conditions, such as: poor ventilation,
•
temperatures below 5℃ or above 35℃.
Do not expose the washer in the place with causticity or explosibility gas.(e.g. dust, steam and gas, etc.)
•
Do not install the washer in a bathroom or a room very wet.
•
The washer should not be installed in an outdoor environment, not even where the area is sheltered,
•
because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.
When installing the washer make sure that the four feet are stable and resting on the floor, adjusting
•
them as required, and check that the appliance is perfectly to level using a spirit level.
The washer must not be installed behind a lockable door, a sliding door or a door with a hinge on the
•
opposite side to that of the washer, in such way that a full opening of the washer door is restricted.
After installation of the washer, wait a few hours before starting it so that acclimates to the
•
environmental conditions of the room.
Make sure that the ventilation openings in the base of the washer (if available on your model) are not
•
obstructed by a carpet or other material.
When moving, do not lift the washer by the knobs or detergent drawer, without lifting it by the worktop
•
or top lid; during transport, never rest the door on the trolley.
The washer is fitted with transport bolts to prevent any possible damage to the interior during
•
transport. Before using the machine, it is imperative that the transport bolts are removed. After their
removal, cover the openings with the 4 enclosed plastic caps.
Connect the water inlet hose(s) to the water supply in accordance with the regulations of your local
•
water company.
Use only the new water inlet hose(s) supplied with the washer to connect the washer to water supply.
•
The old water inlet hose(s) should not be reused.
The supply water pressure must be in the 0.03—1.0 MPa range.
•
ELECTRICAL WARNING
It must be possible to disconnect the washer from the power supply by unplugging it if plug is
•
accessible, or by a multi-pole switch installed upstream of the socket in accordance with the wiring rules
and the washer must be earthed in conformity with national electrical safety standards.
When the washer is installed, the mains socket must be within easy reach.
•
When heating, the maximum current of the washer is 10A, so please make sure that the power supply
•
system (voltage, current and the cable) is applicable to the load of the applied appliance.
In order to ensure your safety, you must plug the cable into a socket which connected to earth. And
•
please check your socket to make sure that it is connected with reliable earth correctly.
Do not use extension leads, multiple sockets or adapters.
•
The electrical components must not be accessible to the user after installation.
•
Do not operate this washer when you are wet or barefoot.
•
Do not operate this washer if it has a damaged power cable or plug, if it is not working properly, or if it
•
has been damaged or dropped.
If the supply cord is damaged, it must be replaced with an identical one by the manufacturer, its service
•
agent or similarly qualified persons in order to avoid a hazard – risk of electric shock.
Disconnect the power cord by grasping the plug, not the cord.
•
The washer should not be installed in an outdoor environment, not even where the area is sheltered,
•
because it may be very dangerous to leave it exposed to damp, rain and thunderstorms.
3