Exsys EX-44011-2 Bedienungsanleitung

EX- EX EX - - 44011 44011- 44011 - - 2 / 2 / 44211 2 / 44211 44211- - - 2 2 2
HARDWARE INSTALLATION :
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Comput-
er and gently slide the cover off.
3. Locate an available expansion slot and remove its covers from the rear panel of your
computer. Make sure it is the right expansion slot for the card (see card description)
4. Align the card with the expansion slot, and then gently but firmly, insert the card.
Make sure the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer's cover and the mounting screws.
DRIVER INSTALLATION :
Windows 9x/2000/XP/Vista & 7:
After starting Windows it recognizes a new "PCI Controller" and opens the hardware
assistant. Please choose manual installation and put the driver CD into your CD-Rom
drive. Now enter the Path "D:\IO\OXFORD2\" and then the directory of your operating
system into the box for the Path/Source and click at >next/continue<. Now Windows
searches for the drivers in the specified directory. Follow the hardware assistant and
finish the installation. If Windows recognizes other new devices repeat the above de-
scribed steps. Attention! Restart Windows in any case after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at >Start< >Run< then enter "compmgmt.msc" and click at >OK<. In the win-
dows that opens select >Device Manager<. Under „Ports (COM and LPT)" you
should find a new „PCI Port" as sample (LPT2). If you see this or similar entries the
card is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example LPT3 to LPT 1, open the >Device Man-
ager< click at >LPT3<, >Settings< and then >Advance<. There you can choose between
LPT1 to 3.
Windows Server 200x:
After starting Windows it recognizes a new "PCI Controller" and opens the hardware
assistant. Please choose manual installation and put the driver CD into your CD-Rom
drive. Now enter the Path "D:\IO\OXFORD2\" and then the directory of your operating
system for Server 2000: "2000", for Server 2003: "XP32" or "XP64", for den Server
2008: „Vista32" or „Vista64" and for the Server 2008 R2: „Win7_32bit" or Win7_64bit"
into the box for the Path/Source and click at >next/continue<. Now Windows searches
for the drivers in the specified directory. Follow the hardware assistant and finish the
installation. If Windows recognizes other new devices repeat the above described
steps. Attention! Restart Windows in any case after installing the drivers.
CHECK THE INSTALLED DRIVER:
Click at >Start< >Run< then enter "compmgmt.msc" and click at >OK<. In the win-
dows that opens select >Device Manager<. Under „Ports (COM and LPT)" you
should find a new „PCI Port" as sample (LPT2). If you see this or similar entries the
card is installed correctly.
CHANGE PORT NUMBER:
If you like to change the port number for example LPT3 to LPT 1, open the >Device Man-
ager< click at >LPT3<, >Settings< and then >Advance<. There you can choose between
LPT1 to 3.
5
English English English EX- EX EX - - 44011- 44011 44011 - - 2 / 44211 2 / 44211 2 / 44211- - - 2 2 2
DRIVER INSTALLATION :
LINUX:
There are no drivers available for Linux, but the card is supported by the most versions
of Linux. Because each individual distribution and kernel version of Linux is different,
sadly we cant provide a installation instruction. Please refer to the installation manual
for standard IO ports from your Linux version! In some newer versions the card will
even be installed automatically after starting Linux.
English English English
P1: 25 Pin Buchse
Die EX-44011-2 ist eine PCI-Express parallel Karte mit einem parallelen EPP/ECP Bi-
Direktionalen Ausgang für den Anschluss von Peripheriegeräten mit Enhanced Centro-
nics Interface (z.B. Drucker, Scanner, Laufwerke usw.). Der serielle PCI-Express Bus
unterstützt optimal die Leistung der Karte. Die Ex-44011-2 unterstützt alle PCI-Express
Slots von x1 bis x16. Es ist nicht möglich die I/O Adressen und Interrupts manuell
einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim Installieren
des Betriebssystems automatisch vorgenommen werden. Bei der Ex-44211-2 handelt
es sich um eine Low Profile Karte (8cm Slot). Beide Karten sind 2003 WHQL zertifiziert.
Kompatibilität:
Betriebs Systeme:
Anschlüsse:
Lieferumfang:
Zertifikate:
Wenn Sie die Karte installieren, beachten Sie bitte die folgenden Hinweise. Da es große
Unterschiede bei Computern gibt, können wir Ihnen nur eine generelle Anleitung zum
Einbau geben. Bei Unklarheiten halten Sie sich bitte an die Bedienungsanleitung Ihres
Computersystems.
6
Bedienungsanleitung Bedienungsanleitung
Vers. 1.0 / 30.06.11
AUFBAU :
Parallel Ausgang
Bi-Direktional
BESCHREIBUNG & TECHNISCHE DATEN :
PCI Express x1 bis x16
WIN ME/2000/XP/Vista/7/Server 200x/(Linux vom OS)
1 x 25 Pin Sub-D Buchse
EX-44011-2 oder 44211-2, Treiber CD, Deutsche Anleitung
CE CE CE CE
/ FCC / RoHS / WEEE DE97424562 / WHQL
JUMPER EINSTELLUNG & ANSCHLÜSSE:
DB 25F: Parallel 25 Pin Buchse (P1):
Pin Signal Pin Signal
1 STROBE 10 ACKNOWLEDGE
2 DATA 0 11 BUSY
3 DATA 1 12 PAPER EMPTY
4 DATA 2 13 SELECT
5 DATA 3 14 AUTO FEED
6 DATA 4 15 ERROR
7 DATA 5 16
8 DATA 6 17 SELECT INPUT
9 DATA 7 18 GROUND
HARDWARE INSTALLATION :
1
PCI-Express Bridge
Parallel Chip EPP/ECP
mit 32-Byte Buffer und
PCI-Bridge
Pin Signal
19 GROUND
20 GROUND
21 GROUND
22 GROUND
23 GROUND
24 GROUND
INIT 25 GROUND