Replacement Of Battery For Memory Protection; Resetting The Unit - Sharp EL-2901PIII Bedienungsanleitung

REPLACEMENT OF BATTERY
FOR MEMORY PROTECTION
Time for battery replacement
Life of the memory protection battery is approximately 2,500 hours at
25°C(77°F) with the power plug not connected to the socket.
* When the memory protection battery is weak, the date/time setting is initialized
(1/1/2006, 12:00:00 a.m.).
Verify the date/time setting in the date/clock display mode when connecting
the power plug to the socket.
If the date/time setting is modified or incorrect, promptly replace the memory
protection battery with new one.
(The life of the pre-installed battery may be shorter than expected because of
the time the calculator spends during shipment.)
Method of battery replacement
Use one lithium battery (CR2032).
Caution: Replacing the battery will clear the date and time settings, and the
stored tax rate.
1) Turn the power switch "OFF" and unplug the power supply plug from the
outlet.
2) Remove the battery cover on the back of the unit. (Fig. 1)
3) Remove the exhausted battery and install one new lithium battery. Wipe the
battery well with a dry cloth and place the plus "+" side upward. (Fig. 2)
4) Replace the battery cover by reversing the removal procedure.
5) Press the RESET switch on the back of the unit (See "RESETTING THE
UNIT").
Fig. 1
After battery replacement
• Connect the power supply plug to an outlet and turn the power switch "ON".
Check that "0." is displayed. If "0." is not displayed, remove the battery,
reinstall it, and check the display again.
• Readjust date, time, and tax rate settings.
• On the battery replacement date label found on the back of the unit, write
down the month and year when the battery is replaced, as a reference for
the next battery replacement.
Precautions on battery use
• Do not leave an exhausted battery in the equipment.
• Do not expose the battery to water or flame, and do not take it apart.
• Store batteries out of the reach of small children.
SPECIFICATIONS
Operating capacity: 12 digits
Power supply:
Operating: AC: 220V-230V, 50Hz
Memory backup: 3V ... (DC) (Lithium battery CR2032 × 1)
Memory Protection Battery lifespan:
About 2,500 hours (While at 25°C (77°F), and the power plug is not
connected to the socket.)
CLOCK SECTION
Accuracy: Within ±90 seconds per month average (at 25°C(77°F))
Items to be displayed: day, month, year, hour, minute, second
Items to be printed: day, month, year, hour, minute
Time system: 24 hour
PRINTING SECTION
Printer: Mechanical printer
Printing speed: Approx. 2.1 lines/sec.
(At temperature 25°C (77°F), when "741•9 + " is printed. The printing speed
will vary with the number of rows and the figure types to be printed.)
Printing paper: 57 mm(2-1/4") - 58 mm(2-9/32") wide 80 mm(3-5/32") in
diameter (max.)
Operating temperature: 0°C – 40°C (32°F – 104°F)
Power consumption: 51 mA
Fig. 2
3
Dimensions: 193 mm (W) × 255 mm (D) × 60.5 mm (H)
(7-19/32" (W) × 10-1/32" (D) × 2-3/8" (H))
Weight: Approx. 1.02 kg (2.25 lb.) (with battery)
Accessories:
1 lithium battery(installed), 1 battery replacement date label (attached on
the unit's back body), 1 paper roll, 1 ink roller (installed), and operation
manual
WARNING
THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED ON THIS
CALCULATOR. USING THIS CALCULATOR WITH A HIGHER VOLTAGE
THAN THAT WHICH IS SPECIFIED IS DANGEROUS AND MAY RESULT
IN A FIRE OR OTHER TYPE OF ACCIDENT CAUSING DAMAGE. WE
ARE NOT RESPONSIBLE FOR ANY DAMAGE RESULTING FROM USE
OF THIS CALCULATOR WITH A VOLTAGE OTHER THAN THAT WHICH
IS SPECIFIED.

RESETTING THE UNIT

Strong impacts, exposure to electrical fields, or other unusual conditions may
render the unit inoperative, and pressing the keys will have no effect. If this
occurs, you will have to press the RESET switch on the bottom of the unit.
The RESET switch should be pressed only when:
• an abnormal event occurs and all keys are disabled.
Notes:
• Pressing the RESET switch will clear the date and time settings, the tax
rate setting, and the contents of memory.
• Use only a ballpoint pen to press the RESET switch. Do not use anything
breakable or anything with a sharp tip, such as a needle.
• After pressing the RESET switch, connect the power supply plug to an
outlet. Turn the power switch "ON" and check that "0." is displayed.