Engenius EP800H Bedienungsanleitung Seite 27

character).
(3) Press SAVE (Left) soft key to confirm setting.
Re: Once entering the custom name, the greeting of LCD in standby
mode will be changed as the entering.
Defalut greeting is "EP800H".
h. Press 8 to Change Password:
(1) Enter original password (4 digits) of handset then press
soft key when enter this menu.
(2) Enter new password (4 digits) then press
confirm new password.
i. Press 9 to set Headset Ring: See Headset Ring operation on Page
47.
7. Press 6 to set Base Settings:
When enter this menu, you must enter Base PIN code first (4 digits).
Re: The PIN code is for Base Settings. Default is "0000".
a. Press 1 to set DTMF Duration.
Enter the DTMF duration (90~200ms), press
(1)
confirm the setting. Default is 100ms.
Re: Please check with your dealer before you change it. If the duration
not matches with PSTN or PBX setting, it may operate faultily.
b. Press 2 select flash key timing. Default is 600ms.
(1)
Use or to scroll through option 1~9 (100~900ms). Or
press digit key (1~9) directly.
Press SELECT left soft key to confirm selection.
(2)
Re: The default value (600 ms) works in most areas. Changing this
setting may cause Flash key not working. Change only when you
are certain of the new value would work.
c. Press 3 to set Assign Next HS
Enter 2-digit handset ID followed by pressing
(1)
When register a new handset, the base will assign the specific
(2)
handset ID which assigned in advance to the new handset.
d. Press 4 to set Clear HS
Enter 2-digit handset ID followed by pressing
(1)
The base will erase the handset ID from system.
(2)
e. Press 5 to Change PIN:
Enter the new Base PIN followed by
(1)
Re: Default Base PIN is "0000".
OK
SAVE left soft key to
OK left soft key to
OK left soft key.
OK left soft key.
OK left soft key.
~53~
f. Press
(1)
Re: When setting "on", the EP800H will automatically hang up if the
g. Press
(1)
left
8. Press
Registration operation on Page 32, and Multi-base Setting on Page 44.
9. Press
To avoid mis-setup of Call Settings (MENU-4), Phone Settings (MENU-5)
and Base Settings (MENU-6), you can hide these menus, so that other
handset users won't have chance to mis-settup these settings.
Re: When entering the Menu Display, you have to enter password first.
a. Press
(1)
b. Press
(1)
c. Press
(1)
d. Press
(1)
Re: Select "On" means the menu will be displayed on screen. Select "Off"
means the menu will be hidden.
6 to set Auto Hang Up:
Use CHANGE left soft key to select and confirm on or off. The
far end caller hung up already. However, this function depends on
if there is "dial tone or busy tone" signal sent out by PBX or PSTN,
after the call hung up.
7 to Set Time to support DTMF Caller ID:
Use SAVE left soft key to select and confirm the Date and Time
you have set (see Set Time operation on page 19).
7 to register, de-register handset and set Multi-Base: see Handset
8 to set Menu Display:
1 to set hiding/un-hiding of the Call Settings menu.
Use CHANGE left soft key to select and confirm on or off.
2 to set hiding/un-hiding of the Phone Settings menu.
Use CHANGE left soft key to select and confirm on or off.
3 to set hiding/un-hiding of the Base Settings menu.
Use CHANGE left soft key to select and confirm on or off.
4 to set hiding/un-hiding of the Multi-base Settings menu.
Use CHANGE left soft key to select and confirm on or off.
~54~