Technical Data; Noise/Vibration Information; Battery Charging - Bosch 3 601 HB5 0 Serie Originalbetriebsanleitung

18 | English
(20) Dust extraction hose a)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Cordless multi-cutter
Article number
Rated voltage
No-load speed n
0
Oscillation angle on left/right
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation C) and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20−25 °C with rechargeable battery GBA 12V
3.0Ah.
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.

Noise/Vibration Information

Noise emission values determined according
to EN 62841‑2‑4.
Typically, the A-weighted sound pressure level of the power
tool is 79 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑4:
Sanding: a = 3 m/s 2 , K = 1.5 m/s
h
Cutting with plunge cut saw blade: a
Cutting with segmential saw blade: a
K = 1.5 m/s ,
2
Scraping: a = 8.5 m/s 2 , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
1 609 92A 819 | (01.07.2022)
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
GOP 12V-28
power tool and application tools, keeping their hands warm,
3 601 HB5 0..
and organising workflows correctly.
V= 12
Fitting
min −1 5000−20000 A)
° 1.4
u
kg 1.0−1.2 B)
°C 0 to +35
°C −20 to +50

Battery Charging

u
GBA 12V...
Note: The battery is supplied partially charged. To ensure
GAL 12...
full battery capacity, fully charge the battery in the charger
GAX 18...
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
To remove the battery (3), press the battery release button
(2) and pull the battery to the rear and out of the power tool.
Do not use force to do this.
Battery charge indicator
The three green LEDs on the battery charge indicator (6) in-
2 ,
dicate the state of charge of the battery (3). The battery
= 9 m/s 2 , K = 1.5 m/s 2 ,
charge indicator only lights up for five seconds after start-
h
= 2.5 m/s 2 ,
up.
h
2 .
If no LED lights up after switching the power tool on, then
the battery is defective and must be replaced.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
LED
Continuous lighting 3x green
Continuous lighting 2x green
Continuous lighting 1x green
Flashing light 1x green
Flashing light 3x green
Capacity
≥2/3
≥1/3
<1/3
Reserve
Empty
Bosch Power Tools