Changing The Tool - Bosch 3 601 HB5 0 Serie Originalbetriebsanleitung

Changing the tool

Wear protective gloves when changing tools. There is
u
a risk of injury when touching the application tools.
Selecting an application tool
Please observe the application tools intended for your power
tool.
The following table shows examples of application tools. You can find additional application tools in Bosch's extensive range of
accessories.
Application tool
AIZ 10 AB
Starlock
10 × 20 mm bi-
metal plunge cut
saw blade for wood
and metal
AIZ 32 EPC
Starlock
32 × 50 mm HCS
plunge cut saw
blade for wood
AIZ 32 APB
Starlock
32 × 50 mm bi-
metal plunge cut
saw blade for wood
and metal
AIZ 32 BSPB
Starlock
32 × 50 mm bi-
metal plunge cut
saw blade for hard-
wood
AIZ 32 AT/
AIZ 32 AIT
Starlock
32 × 40 mm
carbide plunge cut
saw blade for metal
AIZ 32 APT/
AIZ 32 APIT
Starlock
32 × 40 mm
carbide plunge cut
saw blade for
multi-material
AYZ 53 BPB
Starlock
53 × 40 mm
plunge cut saw
blade for multi-
material
Bosch Power Tools
Application tool
Material Application
Softwood, soft plastics, Smaller separation and plunge cuts; delicate adjustment
gypsum, thin-walled alu- work in wood;
minium and non-ferrous Example: Cutting recess for cable, plunge cuts in gypsum
metal profiles, thin metal boards, resawing recesses for locks and fittings
sheets, non-hardened
nails and bolts
Softwood Splinter-free separation and plunge saw cuts thanks to
round sawing edge (Curved-Tec); also for sawing close to
the edge, in corners and difficult-to-access areas;
Example: Plunge cut for the installation of a ventilation
grille or recess for plug sockets
Composite materials Tear-free flush cuts and plunge cuts in wood, soft non-fer-
made from wood and soft rous metals and plastic thanks to round sawing edge
non-ferrous metals, un- (Curved-Tec);
hardened nails and Example: Recess for plug sockets and pipes, flush cuts
screws, pipes made from through unhardened nails and screws
non-ferrous metal and
profiles with small dimen-
sions
Hardwood, laminated Splinter-free separation and plunge cuts in coated boards
boards or hardwood thanks to round sawing edge (Curved-Tec),
Japan toothing specially suited for hardwood;
Example: Installation of skylights, recess for plug sockets
Hard ferrous metals, ex- Sawing extremely abrasive materials or hard ferrous
tremely abrasive materi- metals; long service life thanks to BOSCH carbide techno-
als, fibreglass, plaster- logy;
board, cement-bonded Example: Cutting of kitchen front covers, simple sawing
fibreboards, hardened through hardened nails and stainless steel
nails and screws
Hard ferrous sheet metal, Splinter-free separating cuts and plunge cuts in sheet
epoxy, plasterboard, metal thanks to round sawing edge (Curved-Tec); long ser-
GFRP, CFRP, cement vice life thanks to BOSCH carbide technology;
fibreboard Example: Sawing through sheet metal, cutting through
screws in window frames
Gypsum boards, chip- Optimised for plunge saw cuts with a subsequent longer
boards, sandwich mater- separation cut; the Dual-Tec shape ensures a clean and
ial, wood complete cut both in the corners and during a longer sep-
aration cut;
Example: Plug socket recesses in gypsum boards or
wooden walls
English | 19
GOP 12V-28
1 609 92A 819 | (01.07.2022)