Lcd Display; On/Off And Autotest; Pressure Relief Valve - Osprey SOELDEN Bedienungsanleitung

Vorschau ausblenden

Inhalt

Inhaltsverzeichnis

Verfügbare Sprachen

MICRO USB-C

PORT

The

micro-USB-C port (5V – 3A)

Charging can be completed with a standard

the

micro-USB-C

cable takes priority over recharging via the 2

The SuperCapacitors can be recharged with the

ON / OFF AND AUTO-TEST

To turn on the

OSPREY ALPRIDE E2 AIRBAG System,

To turn on the E2 System, use the ON / OFF switch. This safety switch

This safety switch prevents undesired activation inside the bag. Pull the

prevents undesired activation inside the bag. Pull the switch up, turn it

switch up, turn it clockwise and hold for 2 seconds.

clockwise and hold for 2 seconds.

Each time it is turned on, the

OSPREY ALPRIDE E2 AIRBAG System

Each time it is turned on, the E2 System conducts an auto-test to verify

an auto-test to verify that the motor, SuperCapacitors and electronics are

functioning properly.

that the motor, SuperCapacitors and electronics are functioning properly.

During this self-test, the 3

LEDs

During this self-test, the 3 LEDs light up chronologically to check that the

LEDs

are functioning. Simultaneously, the

LEDs are functioning. Simultaneously, the LCD display blinks to check

the

LCD

display is working properly and all icons are visible.

that the LCD display is working properly and all icons are visible.

During this auto-test, the motor completes a first rotation at lowspeed,

During this auto-test, the motor completes a ﬁrst rotation at low

switching on the green LED.

speed, switching on the green LED.

If the auto-test is succesfully completed, the motor rotates a second time and the green / orange

If the auto-test is succesfully completed, the motor rotates a second time and the green / orange LED will blink

>The system is ready for use.

If the auto-test detects a malfunction, the motor will rotate 4x and the red

If the auto-test detects a malfunction, the motor will rotate 4x and the red LED will remain on There is a problem in the system and it is not

problem in the system and it is not operational.

operational.

If the system detects a malfunction and it is charging, the red LED will remain on and the orange LED will blink rapidly.

If the system detects a malfunction and it is charging, the red

If there is a failure during the self-test, the following icon will be displayed on the LCD:

To turn the system OFF, pull the switch and turn it clockwise (same procedure as for turning ON). The motor will rotate 1 x and the red

To turn the system OFF, pull the switch and turn it clockwise (same procedure as for turning ON). The motor will rotate 1 x and the red LED will turn

on and off again to indicate that the system has shut down.

NOTE: The LED blinking speed indicates that the system is either charging (2 x per second) or in standard ON mode (1 x every 3 seconds).

NOTE: The

LED

blinking speed indicates that the system is either charging (2 x per second) or in standard ON mode (1 x every 3 seconds).

TERRAIN USE AND LED STATUSES

TERRAIN USE AND

LED

To use the OSPREY ALPRIDE E2 AIRBAG system on terrain, you will need to:

To use the E2 System on terrain, you will need to:

To use the

E2 System

on terrain, you will need to:

1- Turn ON the

E2 System

(see section 5)

1- Turn ON the E2 System (see section 5)

2- Verify that the auto-test is okay (see section 5)

If the green

LED

blinks, the system is operational with at least six hours of autonomy.

If the green LED blinks, the system is operational with at least six hours of autonomy

If the orange

LED

blinks, the system is operational with less than six hours of autonomy.

If the orange LED blinks, the system is operational with less than six hours of autonomy.

If the red

LED

blinks, the system cannot guarantee 100% inflation (but it will still attempt to inflate the airbag as much as possible).

If the red LED blinks, the system cannot guarantee 100% inﬂation (but it will still attempt to inﬂate the airbag as much as possible).

If the red

LED

remains on, the system is defective and should not be used.

If the red LED remains on, the system is defective and should not be used.

NOTE: The

LED

blinking speed indicates that the system is either charging (4 x per second) or in standard ON mode (1 x every 10 seconds).

NOTE: The LED blinking speed indicates that the system is either charging (2 x per second) or in standard ON mode (1 x every 3 seconds).

To activate the airbag inflation, pull hard (between 5 to 10 kg) on the activation trigger.

To activate the airbag inﬂation, pull hard (between 5 to 10 kg) on the activation trigger.

LCD

DISPLAY

LCD DISPLAY

PRESSURE RELIEF VALVE

The pressure relief valve is a solenoid-type electric valve and is active 3 minutes after the end of inflation for a maximum of 10 minutes or less depending

on the residual energy in the batteries or SuperCapacitors. It will then close automatically.

As soon as the valve is activated, the following icon appears on the

The purpose of this valve is to reduce the airbag pressure 3 minutes after inflation. This is to reduce the stress on the seams and fabric of the airbag,

ensuring a longer lifespan inflation after inflation.

The pressure relief valve also allows passive and partial deflation of the airbag by reducing its pressure but does not allow complete deflation of the airbag.

The operation of the pressure relief valve is controlled 3x during each self-test and can be clearly heard from the characteristic ticking noise (like a

Swiss watch!)

OSPREY / ALPRIDE E2 AIRBAG SYSTEM | Owners Manual

makes it possible to recharge the SuperCapacitors using the

USB-C

charger (not included), like those used for cell phones. Recharging the SuperCapacitors with

micro-USB-C

cable even in the absence of the

use the ON / OFF switch.

light up chronologically to check that the

LCD

display blinks to check that

STATUSES