Disposal Information - 3M 88757 Bedienungsanleitung

Temperature Overheat System
The tool has the ability to monitor its temperature. If the temperature reaches a damaging level, the tool will go into a protective mode that will limit the speed and
power output until normal temperature is reached.
CLEANING
1. Periodically blow out all air passages and area above Disc Pad and under shroud with dry compressed air. All plastic parts should be cleaned with a soft damp
cloth. NEVER use solvents to clean plastic parts.
2. Wear safety glasses while using compressed air.
HEALTH AND SAFETY INFORMATION
Disclaimer: 3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace
use. Unless specifi cally stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use
by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or
literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product
literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, fi eld action, or other product use notice.
Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. For help with product selection and use,
consult your on-site safety professional, industrial hygienist, or other subject matter expert. For additional product information, visit www.3M.com.

DISPOSAL INFORMATION

Waste Electrical & Electronic Equipment (WEEE) Compliant
• Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
• Contact your local government for information regarding the collection systems available.
• If electrical appliances are disposed of in landfi lls or dumps, hazardous substances can leak into the groundwater and get into the food chain,
damaging your health and wellbeing.
• When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge.
Federal Communications Commission (FCC) Compliance Statement
IMPORTANT NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
NOTICE: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Warranty and Limited Remedy: 3M warrants this tool against defects in workmanship and materials under normal operating conditions for one (1) year from
the date of purchase. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. Many factors beyond 3M's
control and uniquely within user's knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, customer is
solely responsible for evaluating the product and determining whether it is appropriate and suitable for customer's application, including conducting a workplace
hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and
appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property. User must operate the
tool in accordance with all applicable operating instructions, safety precautions, and other procedures stated in the operating manual to be entitled to warranty
coverage. 3M shall have no obligation to repair or replace any tool or part that fails due to normal wear, inadequate or improper maintenance, inadequate
cleaning, non-lubrication, improper operating environment, improper utilities, operator error or misuse, alteration or modifi cation, mishandling, lack of reasonable
care, or due to any accidental cause. If a tool or any part thereof is defective within this warranty period, your exclusive remedy and 3M's sole obligation will be, at
3M's option, to repair or replace the tool or refund the purchase price.
Limitation of Liability: Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising
from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profi ts or business opportunity),
regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.
Submitting a Warranty Claim: Contact your dealer when submitting a warranty claim in accordance with the restrictions listed above. Please note that all
warranty claims are subject to manufacturer's approval. Be sure to keep your sales receipt in a safe place. This must be submitted when fi ling a warranty claim,
within 1 year from the date of purchase. For additional assistance call 1-800-362-3550 (choose option 3, then option 5).
Product Repair after Warranty Has Expired: Repair of 3M Abrasive Power tools that are not under warranty is available through 3M or a 3M Authorized Tool
Repair Representative. Contact your 3M Abrasive Power Tool Distributor for details, or call 1-800-362-3550.
Abrasive Systems Division
3M Center
St. Paul, MN 55144-1000 U.S.A.
www.3M.com/abrasives
10
© 3M 2022.
3M is a trademark of 3M Company.
34-8727-4332-2